rc 450 helicopter 3d models
37245 3d models found related to rc 450 helicopter.thingiverse
... helicopter. ...I think this design should fit most 450 size ones as the designs are almost identical at the bottom. Nice bit of flex to the parts (using ABS) to give a nice soft landing. ... These give the helicopter a 5 degree pitch forward.
grabcad
An incomplete, but nice looking model of my Hobby King Align 450 clone, originally made in Alibre Design and finalised in SolidWorks. Most of the important parts including full metal head and tail are there. ...Decals for rotor blades and canopy...
thingiverse
Please be extremely careful when flying helicopters! This is not a quadcopter, blade strike may cause a serious injury! Do not fly this thing with people around! The printed rotor head or entire transmission frame may blow up in a case of linkage...
thingiverse
This is a rotor blade for a T-Rex 450 RC Helicopter optimized for very stable flight. The lightweight rotors provide much better stability over stock rotor blades. You can print this with supports which creates a very rigid blade preventing flapping,...
thingiverse
After a recent crash, I decided to make a new fin for my KDS450SV. ...Nothing fancy, just functional.
thingiverse
Custom design 450 class RC helicopter. Designed to use align components from any 450 class bird. Recess in side frame is designed to fit the Tarot zxy FBL controller. I have assembled this model and can verify fit. It has yet to be flown as I am...
thingiverse
After a recent crash I noticed that the gyro on my KDS450SV is a bit exposed, so made a small cover thats tough enough to take a flyer strike in the event of a crash.
grabcad
Transmitter: 6CH RTF/ARF RC Helicopter3. Length: 25.8in (655mm)4. Main Rotor Diameter: 28.3in (720mm)5. Tail Rotor Dianeter: 5.3in (135mm)6. Gross Weight: RTF with li-po battery(670g)7. Battery: 11.1V 2200mAh 15C li-polymer8. Motor: Brushless...
thingiverse
fits align / hk 450 solidworks file included for easy customization the hole will probably be tight. ...you should pass it with a 5mm drill and put some wd40 or other lube inside or you will have a hard time removing it from the shaft
thingiverse
Update: I have realised that the PLA is great for avoid damage in helicopter crashes (I have had several last days ;) ). ...PLA main gears acts as a mechanical fuse better than standard gear (ABS), in a crash teeth break apart quickly and avoid damage...
thingiverse
Properties: z = 140, step = 0,5mm Fully functional part.
youmagine
I was looking for a nice solution to mount the antenna in to the 90° angle.The Piece can be pushed to the landing and holts already firm in my case.
thingiverse
A simple battery try to firmly locate the lip at the front of my KDS450 SV. ...Attaches to the existing mounts on the fram.
thingiverse
i have looked and looked for a 3D printable version of the guns on Airwolf and could not find them anywhere plenty of pictures but no files to download so i created these in SOLIDWORKS i hope you guys like them i have also included the Solidworks...
thingiverse
I remixed this to rotate the hole pattern 90 degrees as the motor I was using has the cable exit in the opposite corner. ...Great design to use.
cults3d
3D Printable Model of Eurocopter EC135 For RC 450 Helicopters Attachment STL files to print .G-codes not included
cults3d
3D Printable Model of Eurocopter AS350 Ecureuil For RC 450 Helicopters Attachment STL files to print .G-codes not included
cults3d
3D Printable Model of Bell 222 Airwolf For RC 450 Helicopters Attachment STL files to print .G-codes not included For hobbyists only, not suitable for commercial use
cults3d
3D Printable Model of Bell 206 For RC 450 Helicopters Attachment STL files to print .G-codes not included For hobbyists only, not suitable for commercial use
cults3d
3D Printable Model of MD 500 hughes For RC 450 Helicopters Attachment STL files to print .G-codes not included https://www.facebook.com/MastercraftP3D
cults3d
3D Printable Model of SA341 Gazelle For RC 450 Helicopters Attachment STL files to print .G-codes not included Version 2 https://www.thingiverse.com/thing:4731950 Tail rotor dummy https://www.thingiverse.com/thing:4731930
pinshape
I liked how my 250 helicopter blade holder came out, so I decided to make one for the 450 size helicopter. ...This fits a 12mm boom.
cults3d
3D Printable Blue Thunder Lightning Model for RC 450 Helicopters Attached STL files for printing .does not include G-codes https://www.facebook.com/RC-Blue-Thunder-450-114492903666291/ Tail rotor dummy https://www.thingiverse.com/thing:4731930 For...
thingiverse
These fins are sized to fit Trex 450 style helicopter tails. Check back for more styles and other sizes in my things list. I'm using .8mm walls with 17% triangle infill, makes it very light and reasonably strong. Here is my goto PLA brand: ...