rc driver 3d models
45269 3d models found related to rc driver.thingiverse
Это ремикс Мне нужен был водитель в RC модель Я нарезал его, для удобства печати Уменьшить до 80% для rc это примерно 17 см Есть отдельные части и файл целиком Для соединения я использовал фидерную резину. ... если не открывается файл,надо...
youmagine
Printing Instructions 1x Base (PWM Driver or RC Driver HAT edition) 1x Handle 2x Frame (for front and rear) 2x Screw for Handle (1.2mm walls) 4x Screw for Base (1.2mm walls) 4x Spacer (if needed for clip adjustment) Supported RC Cars Desert Monster...
thingiverse
## Printing Instructions * 1x Base (PWM Driver or RC Driver HAT edition) * 1x Handle * 2x Frame (for front and rear) * 2x Screw for Handle (1.2mm walls) * 4x Screw for Base (1.2mm walls) * 4x Spacer (if needed for clip adjustment) ## Supported RC...
thingiverse
Designed for the self Made Arrma Krayphon some Driver :)
cults3d
This model is meant to be used in 1/10 RC cars with lexan interiors (the ones you can buy from Proline or Injora). ...It's only half body to fit the interior.
thingiverse
very tight fit on the board, maybe need to grind with file the hooks.
thingiverse
Case to carry a driver set for small RC crawler. Fuzzy skin (outer only) option is recommended to rotate the cap easily. Thread of bottom part should be printed without fuzzy skin. I have attached the screenshot of Cura slicer to avoid fuzzy skin...
thingiverse
A device to stop the hex driver from rolling around on the desk.
thingiverse
... Disclaimer: I'm not affiliated with Amazon or Banggood in any way, and not advertising for them. It is just a couple of places to get a tool set like these. Instructions Just print it out, and drop the handles of the drivers down over the pegs.
pinshape
this is a simple race driver for your formula 1 open rc car.. uses a m3 screw to attach it threw the supplied hole in the cockpit.. ... minimal supports needed for the windshield and under the drivers chin..
thingiverse
Holds the 7 piece driver set that is commonly used in RC and other Hobbies on the IKEA Skadis pegboard. It is a remix of CSD_Salzburg's design. You will need to print the 2 hooks (Skadis_Universal_Hook.stl) to go with it these can be found @...
thingiverse
Simple design for Screw driver Holder , so i can find it when i need it (:
thingiverse
This is a Driver for the open rc tractor. https://www.thingiverse.com/thing:1967086 I needed some extra space for the electronics I wanted to fit in the tractor (Speaker, soundmodule), so I came up with the idea of an hollow Driver. So here Comes...
thingiverse
A security helmet and a cap for your truck/car Driver. ... Made for 1/14 cars/trucks Made to pass on this 3D printable Driver : https://www.thingiverse.com/thing:3556065 Casque de chantier = Security Helmet Casquette = Cap
thingiverse
This is a MIP tool holder for the metric and standard hex sets, it also has holes for the MIP speed tips as well(or any 1/4 inch quick chuck bit. ...also has small storage up front.
thingiverse
After printing the "RC Snow Tracks - No Hardware" I realized my standard 1/4" drive 7mm socket was too large to fit in the drive wheel to tighten the wheel nuts so I created this printable version. Print vortically if you can (no supports) with a...
cults3d
EN: The size is standard, so you have to adjust it to the desired one before printing it, for now I have printed it in scales such as 1/24, 1/20, 1/16, 1/12 and 1/10, all of them without any failure of impression. It adapts to any vehicle, to...
thingiverse
A work in Progress. Designed to Mount a servo underneath. This is a prototype. ... Fits TT01 Chassis
grabcad
saya menjadi driver grabcar bukan semata hanya iseng iseng melainkan menganti posisi saya yang sudah tidak berkerja
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=52757 Instructions Using the following options: top_word = Driver text_depth = 3 bottom_word = Peterbilt plate = 155.9 font_scale = 2
cults3d
Quick holder for RC allen drivers. With lid on, drivers that are a max 7" will fit. ...Cavities are setup for a driver that's 0.75" dia across the handle.
thingiverse
Quick holder for RC allen drivers. With lid on, drivers that are a max 7" will fit. ...Cavities are setup for a driver that's 0.75" dia across the handle.