rc driver online 3d models
144432 3d models found related to rc driver online.thingiverse
Это ремикс Мне нужен был водитель в RC модель Я нарезал его, для удобства печати Уменьшить до 80% для rc это примерно 17 см Есть отдельные части и файл целиком Для соединения я использовал фидерную резину. ... если не открывается файл,надо...
youmagine
Printing Instructions 1x Base (PWM Driver or RC Driver HAT edition) 1x Handle 2x Frame (for front and rear) 2x Screw for Handle (1.2mm walls) 4x Screw for Base (1.2mm walls) 4x Spacer (if needed for clip adjustment) Supported RC Cars Desert Monster...
thingiverse
## Printing Instructions * 1x Base (PWM Driver or RC Driver HAT edition) * 1x Handle * 2x Frame (for front and rear) * 2x Screw for Handle (1.2mm walls) * 4x Screw for Base (1.2mm walls) * 4x Spacer (if needed for clip adjustment) ## Supported RC...
pinshape
this is a simple race driver for your formula 1 open rc car.. uses a m3 screw to attach it threw the supplied hole in the cockpit.. ... minimal supports needed for the windshield and under the drivers chin..
thingiverse
This is a Driver for the open rc tractor. https://www.thingiverse.com/thing:1967086 I needed some extra space for the electronics I wanted to fit in the tractor (Speaker, soundmodule), so I came up with the idea of an hollow Driver. So here Comes...
thingiverse
Holds the 7 piece driver set that is commonly used in RC and other Hobbies on the IKEA Skadis pegboard. It is a remix of CSD_Salzburg's design. You will need to print the 2 hooks (Skadis_Universal_Hook.stl) to go with it these can be found @...
thingiverse
Case to carry a driver set for small RC crawler. Fuzzy skin (outer only) option is recommended to rotate the cap easily. Thread of bottom part should be printed without fuzzy skin. I have attached the screenshot of Cura slicer to avoid fuzzy skin...
thingiverse
A device to stop the hex driver from rolling around on the desk.
thingiverse
Simple design for Screw driver Holder , so i can find it when i need it (:
cults3d
A security helmet and a cap for your truck/car Driver. ...Made for 1/14 cars/trucks Made to pass on this 3D printable Driver : https://www.thingiverse.com/thing:3556065 Casque de chantier = Security Helmet Casquette = Cap
thingiverse
A security helmet and a cap for your truck/car Driver. ... Made for 1/14 cars/trucks Made to pass on this 3D printable Driver : https://www.thingiverse.com/thing:3556065 Casque de chantier = Security Helmet Casquette = Cap
thingiverse
very tight fit on the board, maybe need to grind with file the hooks.
cults3d
This is the stl for the RC truck driver 'Felipe' on my Etsy shop. I haven't printed this one myself yet. My models were outsourced to a commercial SLA printer. ...However, the build tolerances are well within the specifications of my Anycubic Photon.
thingiverse
Designed for the self Made Arrma Krayphon some Driver :)
cults3d
This model is meant to be used in 1/10 RC cars with lexan interiors (the ones you can buy from Proline or Injora). ...It's only half body to fit the interior.
grabcad
saya menjadi driver grabcar bukan semata hanya iseng iseng melainkan menganti posisi saya yang sudah tidak berkerja
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=52757 Instructions Using the following options: top_word = Driver text_depth = 3 bottom_word = Peterbilt plate = 155.9 font_scale = 2
thingiverse
After printing the "RC Snow Tracks - No Hardware" I realized my standard 1/4" drive 7mm socket was too large to fit in the drive wheel to tighten the wheel nuts so I created this printable version. Print vortically if you can (no supports) with a...