rc fenders 3d models

Fenders for RC Tank by Staind designed to replace side brackets of tank cover also created by Staind. New cover brackets lift the cover up slightly in the rear providing more space underneath and offer a back cover fully enclosing the interior. I...

Wheels were coming out from under the body. ...So an extender was needed.

FRONT: Left/Right Fenders, Joiner cap, Incognito Mount Front REAR: Left/Right Rear Fender, Bed Cap, Fore Fenders(Fill the gap from the fender to the Running board, Split Tail Cap/Tail Cap with velcro body mounting option, Incognito Mount Rear The...

Fender extension for the 1:10 he 9125. ... Can be easily mirrored.

Here are some fender flares for an R/C car, inspired by the hoonitruck style. Only the right side is included in the files, so mirror it to get the other side. These flares will need to be ground down to fit perfectly on a specific model. ...I...

Front and rear 'Kahn' style fenders are designed for 1:10 scale RC Land Rover D110 models, fitting seamlessly onto RC Modelex bodies - though they may also fit other models. These fender sets can be mirrored or scaled to suit your printing needs...

Fender flares for 1/10 rc cars

Customize Your RC Boat or Model Fender Transform it to fit any size by splitting it into two parts. This flexibility allows you to easily combine different colors and create a unique look for your model. ... Two Ball Designs Span the Length

I remixed the fender flares found here (https://www.thingiverse.com/thing:4645007) to add pockets for some M2 socket head screws. I also rescaled the file to fit 4.19" tires. ...I also made a second version with rounded ends that look a little more like...

I sketched up some fenders for my little trailer. they're screwed on to the axle. no additional hardware needed. ... check my other "things" like the bed for this trailer!

Read Fenders for the Axial Deadbolt, some trimming is necessary, you need 10 bolt of 1.4mm for each of them. ... Both left and right are printed together, they are joint by a small piece of PLA that you must cut.

The new fenders will provide a sleek and aerodynamic appearance to the vehicle, enhancing its overall style and performance. When it comes to printing the fender parts, make sure to use a layer height of 0.20mm for optimal results. This will ensure...

2 axle fenders for Tamiya RC truck - LOW and "+5mm version". ...With mounting holes for this lights: https://www.thingiverse.com/thing:5037927

2 axle fenders for Tamiya RC truck - LOW and "+5mm version". ...With mounting holes for this lights: https://www.thingiverse.com/thing:5037927

These are front fenders for the Axial Deadbolt, some triming of the body is necessary, you need 10 1.4mm bolts to put it in the body.

1/10 RC CAR REAR INNER FENDER custom sase

This is a compact Fender Flare designed specifically for 1/10 scale RC vehicles.

Just my design of a fender flare set

I designed Inner Fenders specifically for the SCX10 II Chassis paired with the XTRA Speed JK Wrangler Body. ...After printing and installing them, I found a perfect fit, prompting me to share my results with others.

Hi, I liked this fender project and thought I would retrofit it for my 1/5 rc bike.

Here you can finde fenders for the RC Jeep Cherokee and RC JEEP Comanche body for front and rear. The fender are more narrow and scale than the original rubber fender. With this fenders you are able to reduce the visual appearence of the fender cut...

Here you can finde fenders for the RC Jeep Cherokee and RC JEEP Comanche body for front and rear. The fender are more narrow and scale than the original rubber fender. With this fenders you are able to reduce the visual appearence of the fender cut...

These are fenders I designed specifically for the Element Enduro Sendero RC crawler. With the original fenders, wheels experience interference when the suspension reaches its lowest point. The clamp pieces have 2.5mm holes that should be tapped with...

RC 1:10 Drift Arch or Fender Flare Use 1.2mm screws to mount to shell, put the middle screw in first, then each end then the others. ... Will fit many models Print super detail PLA+ 200 50 I use a brim

RC 1:10 Drift Arch or Fender Flare Use 1.2mm screws to mount to shell, put the middle screw in first, then each end then the others. ...Will fit many models Print super detail PLA+ 200 50 I use a brim

... that your model needs. Front fender: 26,11 58,93 x 45,31 mm Front fender with trim: 27,61 x 58,93 x 45,31 mm Rear fender: 26,11 x 58,49 x 44,55 mm Rear fender with trim: 26,86 x 58,49 x 44,55 mm Attention: -Take care when you remove the supports

This file is designed for printing on both FDM and SLA large size printers. The body has a division into body elements and has seats for them. Hood with sills, magnetically attached. ...Length: 525mm Width: 276mm Height: 165mm

These flairs fit snugly over the clear lexan edge of the fender cut out, allowing you to glue or add screws from behind for added security. They are compatible with other 1/10 scale bodies, making them a versatile addition to your collection. ... The...

Fender Flares for scale Tamiya Ford F350 1/10 RC. ...STL files for only left side, mirror these for right side.