rc transmitter holder 3d models
404199 3d models found related to rc transmitter holder.
thingiverse
This is a custom-made servo holder specifically designed to accommodate a standard 40x20x40 servo unit. ...Its sturdy construction allows it to stand independently, eliminating the need for any additional support or stabilization.
thingiverse
I'm designing a super simple screwdriver holder that's going to make my life easier by keeping my trusty tool right where I need it, ready to grab whenever the moment calls.
thingiverse
Blade holder designed specifically for the 230 series, requiring a fine-tuning process through sanding to ensure a precise fit with PLA materials. ...In contrast, the TPU semi-flex variant requires minimal to no sanding adjustments.
thingiverse
... with similar dimensions. ...It's designed to be stuck on a flat surface using double-sided tape on the back. The design of the Xiaomi Mi Box S remote control holder allows it to stick firmly onto any smooth surface, thanks to its adhesive backing.
thingiverse
I need a sturdy motor holder that can securely fasten my S2445-3200 Brushless Inrunner (3200kv) or any other motor with a diameter of 23.8mm. ...To do this, I'll require some bolts and nuts to create 5mm holes for a rock-solid fit.
thingiverse
The original battery holder has been found to be slightly too compact to accommodate the nVision 4500mAh LiPos snugly, which measure approximately 139mm in length. This offering serves as a direct replacement for the standard unit. ...Its design may not...
thingiverse
This is a sleek, compact 25mm high SMA antenna holder designed specifically for individuals who prefer mounting their antennas in this style. If you have any requests or suggestions, I'm always open to new ideas and constructive feedback. ...While...
grabcad
Very simple part but I couldn´t find it anywhere.I printed the holder in PLA with 0.22mm of layer because it has a thikness of 0.9mm. ...In my opinion 0.95mm will be the best fit for the helicopter.
thingiverse
It's thing https://www.thingiverse.com/thing:3700617Use parts of sponge rubber to improve adhesion for the inner side and for the base.The M4 holes on model_holder_part1.stl are a little bit undersized. Use a lighter for a few seconds at the M4 screw...
thingiverse
Designed another pill holder for AE/Xray pills. This time with a screw on cap, works pretty well but not always perfect due to the gaps where the pills go so doesnt always catch perfectly but still works well (Updated with a tighter fit now, works...
thingiverse
Hello, this is a GPS holder designed specifically for the Vortex Mojo 230. It is compatible with the ublox m8n mini GPS module, which goes by many different names, as you can see from the attached picture. ... If you need to run a GPS on your Mojo, I...
thingiverse
Battery pack holder for A123 LiFePo4 cells with 2500mAh batteries that measure 65x26mm. Designed to fit 2S and 3S packs, the latter in a triangular shape. You can enlarge drill holes up to 3mm in diameter. Check out the diagrams for precise...
thingiverse
This is a replacement for the included antenna holders. I created mine out of flexible nylon, but any material could probably be used. You might need to get a file in there to clean it up so the antenna tube slides in easily. It has an interference...
thingiverse
I have a DJI Mavic Pro and a tablet mount for it, but the sides of the holder aren't tall enough to grab my rugged outdoor drone body. It's just too thick, so I created custom mounts to secure the hull. Please print each part (backe_innen.stl and...
prusaprinters
Designed another pill holder for AE/Xray pills. This time with a screw on cap, works pretty well but not always perfect due to the gaps where the pills go so doesnt always catch perfectly but still works well (Updated with a tighter fit now, works...
thingiverse
this mod is to use any 1:10 hex wheel instead of the genuine one. ... place this inside the rc wheel and push it gently onto the transmitter steer axle. ...
prusaprinters
With this holder it is possible to attach an Iphone 11 Pro with a mobile phone case. Also tested with an Iphone 13 Pro, which also fits with a mobile phone case.The idea is not mine, but it is a further development of this...
thingiverse
This is a replacement transmitter steering part for the 1/28 Team associated RC car transmitters. I used normal supports and printed with the screw side down. ...My printer isn't 100% tuned so I had to sand down the sides of the pin that goes into the...
thingiverse
This case is designed to fit various Fatshark transmitters, but it's not compatible with the 600mW Immersion RC Transmitter due to a different SMA connector placement. For installation, use self-tapping screws. ...The STL file for this case can be found...
thingiverse
Cross-over strap for transmitter tray performs flawlessly with heavy RC Transmitter setups. Printed successfully in PLA and TPU - both materials yield excellent results. The webbing utilizes 40 mm or 1.5" Nylon strap. ...Glue is applied to the belt's...
thingiverse
I've had a transmitter for my RC planes for a while now. I use it on the simulator on my PC and have found it convenient. To avoid cluttering the table with dead space, I decided to design a small bracket that can be screwed into the wall and holds...