rcbs rock chucker primer system 3d models
129768 3d models found related to rcbs rock chucker primer system.thingiverse
Changes: * Decreased angle of primer spout to give more clearance for attached tube * Widened primer catch to eliminate issue with primers hitting the front sides and bouncing away * Shortened primer catch mouth - the unit was about 1cm taller than...
thingiverse
Thsi Prime catcher has been desgned for an older version of the RCBS Rock Chucker Supreme press, having the outlet for the primers at front side. The catcher can be attached to the press by pressing into the 4 mm holes threads for M3 screws. For...
thingiverse
This is a Remix of https://www.thingiverse.com/thing:3916949 Made it longer to fit the RCBS Rock Chucker II press. This is useful if you want the primers to fall to the bottom of the ram and prevent them from spitting out the front of the ram and...
thingiverse
This holds the primer catcher tray on the RCBS Rock Chucker reloading press. They sure don't make things like they used to. I've only been reloading with this thing for 42 years and already something broke. ...Print Settings Printer Brand: ...
thingiverse
Primer catcher for the rock chucker supreme press. I tried a few of the models out there and they did not work to my satisfaction. This was designed to fit the press with no tools or pins. It has clearances for any rough castings and should fit your...
thingiverse
Have not seen a Primer Catcher for the early model RCBS RC's so drew this one. ... I attach some clear tubing to catch spent primers and use surgical rubber tubing or elastic band to hold to the press
thingiverse
Do spent primers like to escape out the front of your Rock Chucker ram when you're decapping? This plug will fix that. To install: 1. Raise the ram. 2. Slide the plug in from the front until it is sunk below the outer surface of the ram. 3. 4....
thingiverse
... and will likely refine it later but works. Must reverse the RAM for this design and also add a ramp for the primer discharge slot. Print flat with supports for the tube. ... Takes a 1/4-20 bolt to lock it on the press if you want but works without
thingiverse
After success with the Dillon XL650 primer cup support, I was given a broken primer chute for an RCBS Rock Chucker to replicate. The original part was actually two parts, 109145 and 109146 and somehow the front part (109145) was broken (shown in...
thingiverse
Designed this for those that use the old RCBS Rock Chucker A2 Press. Might fit other press rams with the 2 step ram top. ...Slips on and covers the slot so while decapping the old primers are forced down into the hollow ram and into the waste basket.
thingiverse
This is a small guard I created to prevent spent primers from falling into the spring area of my Rock Chucker's universal primer arm when de-capping. I would then have to try and fish them out or put the trash can under it to catch them as they fell....
thingiverse
This replaced the existing primer catcher. ... It puts all the primers into a single section on the left side. ... This is a tension/snap fit part so it might need some clearance work depending on your press dimensions.
thingiverse
Works excellent in conjunction with [RCBS Rockchucker Primer Catcher Remix V3](https://www.thingiverse.com/thing:4250348) by @Snuups as well as with [RCBS Rock Chucker primer slot plug](https://www.thingiverse.com/thing:3916949) by @FishInABarrel...
thingiverse
Tray to mount on a RCBS accessory base plate alongside a Rock Chucker IV. Use existing holes and hardware to mount this tray and make use of the space on the left side of you press. 2 tray sizes. 1 fits in the Accessory Base Plate, and the other is...
cults3d
My version of a primer catcher for RCBS Rock Chucker. Basically same as original with tube adapter that works with case ejector. ... I printed in two pieces and glued together.
thingiverse
My version of a primer catcher for RCBS Rock Chucker. Basically same as original with tube adapter that works with case ejector. ...I printed in two pieces and glued together.
thingiverse
This is a remix from: https://www.thingiverse.com/thing:4548989 - Add a new finger - Add a curvy slide - Add a spacer for flexible slide adjustments - some adjustments to the base
thingiverse
I love the new primer catcher my RCBS Rock Chucker sports:http://www.thingiverse.com/thing:1223108 Might also work with this primer catcher:http://www.thingiverse.com/thing:148190 Or its predecessor:http://www.thingiverse.com/thing:84047 While it...
thingiverse
This is just the primer arm for the priming system of an rcbs rockchucker. This part is discontinued and the only way to get it is calling rcbs and having them send you one. ...I haven't tried printing this yet as I still have mine and mostly made this...
thingiverse
This is a RCBS Summit reloading press "Primer Catcher" design that bolts right up to your existing primer catch screw holes on the press. You can attach a hose that catches the spend primers or redesign the part as needed. ...
thingiverse
This is a retainer for an RCBS Primer catcher. You only get this when you buy a new tray so I decided to print one. ...Feel free to upgrade this to your desire.
thingiverse
A primer catch for my RCBS Summit reloading press, as mine did not come with one. ...I liked the design I ended up with, so I'm publishing it in case anyone else would like one.
thingiverse
Primer catcher for the RCBS Summit press. You'll need 1/2" ID tubing and you might need to dip the tubing in hot water for a minute to get it to slip in place. I secured mine with a wire tie. ... Print at 100% infill.
thingiverse
Occasionally a primer sits on the "shelf" behind the ram but it always ended up getting knocked down the tube by the next primer. I did not include a blocker for the front of the ram. I learned long ago that a drinking straw fills that space nicely...
thingiverse
After trying a couple of designs here, I made my own so I had room for my auto-eject system. As my auto-eject wasn't designed at that point, I made a left-hand and right-hand version of this incase I didn't have room. Designed for the...
thingiverse
This is a primer catcher to be used with RCBS JR2 reloading press so that the primers don't go all over the floor. A trash can can be placed below the spout or some tubing can be attached to direct the spent primers. ...Place the Primer ramp in the slot...
thingiverse
Replacement for the inverted "Y" tray that is supposed to capture primers removed from cases on RCBS Rock Chucker Supreme. This snaps into the same area behind the ram, but is retained by a lug in the slot and a ring that goes around the ram. Remove...
thingiverse
Primer catch tray to be used with common 3D printer primer catcher for the RCBS rock chucker IV. I was recovering unused primers and did not want them going down a tube to the waste bucket. Also works as a work tray on the right side of the press.