rcexplorer 3d models
160 3d models found related to rcexplorer.thingiverse
the downloads page for these models are here: https://rcexplorer.se/downloads/ This is the parts for the bicopter, minus the tilt mechanisms - which you can find [here](https://www.thingiverse.com/thing:4086482). I give no guarantees as to the...
thingiverse
This is a remix from David Windestål, the creator of RCExplorer.se: http://rcexplorer.se/downloads/ This front spacer covers most of the integraded naze board. ...Print Settings Rafts: No ...
thingiverse
STL for the injection molded front spacer required for the new F3FC from RCExplorer (http://rcexplorer.se/product/f3fc-tricopter-frame-with-integrated-power-distribution/) And optional modified spacer for 3mm screw inserts (custom canopy)
grabcad
Racing canopy for RCExplorer V3, V3.5 and mini tricopters. Use five 40mm standoffs and 18 M3x12 screws to assemble the canopy. ...Optionally glue the antenna holders into place and use a M3 plastic tube to guide the antenna wires clear of the...
thingiverse
This is a design for rcexplorer's tricopter v2.5 http://rcexplorer.se/projects/2011/09/the-tricopter-v2-5/ Instructions The two STL files are for the top and bottom of the body of the tricopter. I used 10mm square armatures and bolted the frame...
thingiverse
Custom middle plates and motor mounts for RCExplorers Tricopter V3. Allows you to mount Naze32 Flight Controller. Print all parts from ABS ,solid. You need the following to complete your build( If you don't own the kit) : Aluminium Booms - 12mm or 10...
thingiverse
the downloads page for these models are here: https://rcexplorer.se/downloads/ This is the tilt mechanism used in most of his designs, you'll need 2 for the bicopter and 1 for the tricopters. You also need a servo with a feedback wire - the...
thingiverse
For the spacers you will need longer screws than supplied by RCExplorer.se as the screws need to be longer to get a good grip on the original 40mm spacers. I'd recommend cutting M5 (inner diameter 3mm) aluminium tubes to length instead of printing...
thingiverse
... nuts. I've also integrated pin holes to accept similar camera mount isolation hangers as used in the latest design. (http://rcexplorer.se/wp-content/uploads/2012/09/trihv27-2.jpg) I haven't yet assembled this, so I can't guarantee it works at all.
thingiverse
... Be aware that this canopy 100% requires RCE Bicopter frame and winglets. For best printing results, Oynx-CF is ideal. See the following thread for further details. https://rcexplorer.se/forums/topic/bicopter-camera-mount/#post-60958
thingiverse
Rcexplorer TricopterV4 FPV Cam mount for standard RunCam Sky+ like cameras. ...Print this object twice to use it.
pinshape
Summary Rcexplorer TricopterV4 FPV Cam mount for standard RunCam Sky+ like cameras. ...Print this object twice to use it.
youmagine
This camera mount fits on the RcExplorer Mini Tricopter and allows the fitment of a HS1177 camera, and ones of similar form factor. ... 10/02/17 - V2 uploaded, pushes the camera back 1.5mm for easier fitment.
thingiverse
Impossible tilt pack for the RCExplorer Bicopter: https://rcexplorer.se/product/bicopter-kit/ Hole spacing 16x16 - use 2 M3x6 screws for motors if you have 16x19 pattern, modern 16x16 motors fell free to use 4 M3x6 screws. Use two M3 washers, one...
thingiverse
To minimize boom breakage, use the mechanical fuse version (MF) Buy the original Tricopter and carbon landing gear from http://www.RCExplorer.se Instructions Front landing gear and motor mounts are attached to 10 mm square carbon fiber booms with...
thingiverse
When printed with flex filament, this thing is a durable elastic landing gear for the RCExplorer Tricopter. Instead of relying on breaking zip-ties, the elasticity of the landing gears should protect the copter from all but the heaviest landings. ...
thingiverse
I grew tired of tie wraps breaking on even a slightly bounced landing with my rcexplorer tricopter. So I developed these flex legs for the tricopter. They will work with any 10mm square tube so these legs are not limited to the tricopter, but any...
thingiverse
... following thread for further details. https://rcexplorer.se/forums/topic/bicopter-camera-mount/#post-60958 Video of one of my flights but be aware that my self leveling acted up as I was trying to land. Had to ditch it to keep it from flying off.
thingiverse
Rcexplorer Tricopter V4 TBS Unify Antenna mount
pinshape
Summary Rcexplorer Tricopter V4 TBS Unify Antenna mount
prusaprinters
Rcexplorer Tricopter V4 TBS Unify Antenna mount Category: R/C Vehicles
thingiverse
Board camera protector (RunCam, Foxeer, etc) for RCExplorer Baby Tricopter. ...https://rcexplorer.se/product/babytricopter-kit-with-f3fc-racing-and-pdb/ 2017/03/15: Added clip-on version. ...2018/03/22: Added Fusion360 source file.
thingiverse
Small landing gear/leg designed for RCExplorer Mini Tricopter (http://rcexplorer.se/product/minitricopter-kit/) Print Settings Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 50% Notes: Successfully printed with PLA, 0.2mm layer, 50%...
thingiverse
This mount allows for an easy 45 degree rotation of the tilt axis for the RCExplorer BiCopter. ... Slips on the 10x10mm Carbon Tube and the tilt is then mounted to the 45 degree printed beam.
thingiverse
Canopy for the RCExplorer tricopter V3 (and mini) Print solid with support. Works best with hex screws at the boom fold. ...Use antenna boom for securing it at the front, barbecue skewer at the back.
thingiverse
Use ten M3x20 hex for the frame Use ten M3 lock nuts Use one M3x35 for the tilt mechanism Use Afro 20A slim ESCs Use Multistar Elite 2204 2300Kv for motors Use 6x3" gemfan carbon props Use Flip32+ flight controller Use 6+ channel radio Use 3S up to...
thingiverse
Has markings for center of gravity and mount point alignment for screws found on the RCExplorer Tricopter V3 (can be ordered from http://www.RCExplorer.se) Mount with anti vibration tape on frame aligning markings with top row of bolts for the tail...
thingiverse
This mount makes it easier to effectively secure a GoPro Session to the RcExplorer MiniTricopter. It requires a few zip-ties to mount to the RcExplorer camera plate. It requires a 20mm or narrower velcro strap to secure the Session. The 15 degree...
thingiverse
:-) Bonus material are two antenna holders for the Rx antennae :-) (boom and 3mm plastic pole) Get the RCExplorer Tricopter V3 frame at http://www.rcexplorer.se Instructions Print the parts standing on the print bed as they would be mounted, with...
thingiverse
Adapter for fittingboard cameras with casing like: RunCam Arrow RunCam Swift RunCam Owl Plus Foxeer HS1189 To the RCExplorer and custom RXExplorer canopy. Use board camera screws for permanent fixture, or elastic bands for controlled point of failure...