realacc x210 combo 3d models
6346 3d models found related to realacc x210 combo.thingiverse
Used for Realacc X210 frame, no screws needed, just use cable tie fix, easy to replacement.
thingiverse
Mobius / action cam mount for the REALACC X210 and quads alike.
thingiverse
Front buzzer for realacc x210, buzzer measure: 12mm diameter Print Settings Printer: Hta3D Supports: Yes Infill: 25%
thingiverse
This is a canopy for the realacc X210 frame I used 25mm standoffs in the back and M3x12mm screws in the front with a M3 locknut.
thingiverse
Booty-and-Softmount-in-1 for the Realacc X210 frame Print Settings Printer: Malyan M150 Rafts: No Supports: Yes Resolution: 0.3 Infill: 30-50%
thingiverse
UXII Antenna mount for Realacc X210. It could be mounted right to standoffs. ... Made specially for using with this - https://www.thingiverse.com/thing:2529660 canopy
thingiverse
2mm longer screws are required. Beschreibung (DE): Ein Motor Schutz für das Frame Realacc - X210. ...Es werden 2mm längere Schrauben benötigt. Made: Made of PLA red (Verbatine) Extruder temperature: 220°C Glass bed temperature: 50°C Resolution: 0.20...
thingiverse
12/10/2016 A support for the rx FrSky XSR and a frame Realacc X210. ...12/21/2016 update the support with other exit for the antennas and bigger
thingiverse
New ED.04, are suitable for Ø28mm motors, one high and one low model Realacc X210 Motor Protector, for frame 4mm. Rotate 180º before print , flat side on bed. ...Material: flexible / TPU
thingiverse
Realacc X210 motor guard Made of PLA Black Extruder temperature: 209°C Glass bed temperature: 54°C Resolution: 0.20 mm Infill: 50% Support: No weight 9.4 grams 1pc
thingiverse
Shells: 4 Infill: >15% XT60-210.stl more space inside XT60-210_reelacc_v2.stl flush with frame, antenna holes 3mm XT60-210_v2_pro.stl Realacc X210 Pro LED Board Rig only for "Pro Edition"
thingiverse
VTX/Receiver antenna mount for Realacc X210 Pro that allows use of LED board. Holds 3mm antenna tubes to protect receiver antennas from crash damage. ... I used some additional 8mm washers under standoff screws for some additional support being printed...
thingiverse
... i crashed one Antenna after another. So iI decided to protect them. This antenna protector / stabilisator is designed for the Realacc x210 wit the antenna mount on the right side of the back. ... My antenna hold its position after three crashs.
thingiverse
This cover is designed for the Realacc X210. I installed: -Hobbywing Omnibus 40A 4in1 esc -Hobbywing XRotor F4 FC -TBS mounting plate -TBS Unify Pro HV -X4R FrSky -Runcam Eagle 2 Pro -Brotherhobby Returner R5 Deadpool -Foxeer antenna If...
thingiverse
Pod for the realacc x210 pro. Printed with flexible filament and simplify 3d. Print time 3.5h Made for a foxeer HS1177 and a TBS Unify pro. Change forward with backwards of the CFK frame. Put the Matek PDB with components down and the battery joint...
thingiverse
First version of the realacc x210 pro. I am still working on it and other versions will follow. I added an opening on both sides for the matek pdb and a small opening for an usb but it is on the right side and for usb that is in the middle or a but...
thingiverse
Because my VTX-Antenna connection broke after a crash with my realacc x210 i desided to make a flexible TPU holder for both antennas (vtx and receiver). I really surprised how it came out, It has the right strength and is not too weak by flying...
thingiverse
This is a mounting system for the RealAcc x210 V+ quad frame and the FRSKY XM+ receiver. There are two holes in the top of the frame that seem perfect for running the two receiver antennas through, but it could use a bit of protection. This fits over...
cults3d
Nice mount for TBS Unify Antenna on the back of X210. ... Printed in TPU
thingiverse
A little turtle fin for the Realacc 210 frame. ...It should work with the QAVX, too.