really really really ridiculously good looking 3d models

... Ce(tte) œuvre est mise à disposition selon les termes de la Licence Creative Commons Attribution 4.0 International. Really really ridiculously good-looking pencil holder. by mikebattaglia is licensed under theCreative Commons - Attribution license.

I designed this pencil holder in Rhino 3d. Now, you may be thinking.. "but I can only fit 5 or 6 pens and pencils in there." Well, this is true but I realized that no matter how many pencils and pens I have on my desk, I always grab the same 1 or...

Customized version of https://www.thingiverse.com/thing:4614 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4614

Sometimes I just look at things and go "Really?".... now I can mark them with this awesome REALLY? ...stamp (in all caps to drive the point home)

Not printable as-is

has a good content and it’s really cute

It’s really shiny!!

Really Simple Animatronic Tail

really bad torch

Really constipated duck-face aaa

A model of a really cheap chair

A really cool ring, it can be unisex, works really well in any colour filament

A really simple headphone stand. ... It can printing very easy.

Really strong. ...You could lift an engine block with these. Well, not really... ...But you get the idea.

This is an organization divider for a 0.14 liter Really Useful Box enjoy!!

This is a really bad coaster. It will spill your drink every time. ... I haven't printed one because I value my time.

An S-hook design that holds up. ...You could lift an engine block with this. Well, not really... ...but you get the idea.

This is a really cool pencil holder! It has the word "pencils" protruding out the side. ...I would suggest setting print size to 150%. 

This is a remix of the F104- Printable by Rt45. ... Really nice model but in Simplify a small hole was present in the left reactor entry. Half cut, mirrored, merged and tadaa !!! ...(Thanks to FreeCAD)

Do you need to store more things in a Really useful 0.14 litre box in something like...

This is a really simple camera mount that should be pretty universal . Designed to attached to the rear belt holder on a A30 and A20 Geeetech printer with a couple of cable tie holes to secure the camera. ... Requires you to replace the bolt with an...

A really simple toothbrush holder to hold four thoothbrushes. Simply print then with either double sided tape or a 3M tab stick the toothbrush holder where you need it. Instructions Printed with...

https://learn.adafruit.com/really-simple-animatronic-tail https://www.youtube.com/watch?v=Qn27Ye0vWRQ Animatronics is tricky. It requires mechanical engineering in addition to the software and electrical engineering of most of our projects. Normally...

... Please, visit the model page on our website if you need any additional services. We greatly appreciate you choosing our 3D models and hope they will be of use. We look forward to continuously dealing with you. ...Humster3D Team Sincerely Yours,

If you are looking for one day project- Go with this one ;D Material list: ->4mm steel rod, You will have to cut it into 9mm pieces(x8) (optional but highly recommended) ->4x M3 screws ( I used hex but normal ones should fit as well) ->4x M3 nuts...

Maxed out the build height on the Prusa i3 MK3S. Printed the base with 0.3mm and the rest with 0.15mm layer height. I recommend using a brim (5 - 10mm). PS: You can use it to brush your cat, too! ...My cat Rufus loves it!

<p>Maxed out the build height on the Prusa i3 MK3S. Printed the base with 0.3mm and the rest with 0.15mm layer height. I recommend using a brim (5 - 10mm).</p><p>PS: You can use it to brush your cat, too! ...My cat Rufus loves it!</p><h3>Print...

It is really cool

Spreader really done.

Really nothing to say here, Print how you want. ... if you have any questions put them in the comments :)