rear bag rider 3d models

This is a rear bag rider for the KRG Bravo Chassis. I know that it works on the 700SA Bravo but I am not positive that it will work on other versions - I don't see why it wouldn't though since they don't market theirs as for specific Bravo's. It fits...

I designed this mount to add the Cadex rear bag rider to my Tikka T3x Tac A1. ... You'll need 1* 8-32*1" bolt and the nut that goes with it to be able to mount it on the rifle.

MDT oryx bag rider one is more flat and the other is more round

This is a bag rider for a Foundation Centurion stock. ...It leaves a gap for filling in some attachment method.

First iteration of an M-Lok Bag Rider for MDT buttstocks. ... The units are .0001 of an inch so you need to scale 2540% for MM.

A bag rider for the GRS Bifrost Stock, the standard stock has a picatinny rail that does not work optimally of shooting bags. I've added a longer version as I found the first one to be slightly shorter than ideal, it fits under the butt pad when...

I hacked up a picatinney gopro mount from xxxx to make this Ruger Precision bag rider for my stock. Hope you enjoy. I used the following thingiverse items to help me make the bag rider. This was used to make the picatinney part: Weaver/Picatinny...

Made this to give the rear of my Magpul Pro 700 chassis little more reach to my rear bag. Fits snuggly on the rear with 2 x M-Lok attachments. Edges on the top help to center the part on the chassis. ...

This is a straight bolt on to replace the picatnny rail on the bottom of the Tikka Tac A1 butt stock. ...It uses the original screws to attach. The bag rider works a lot better with a rear bag than the original piece of rail that the rifle comes with.

... rest is used. ...When shotting of bipods with distinct different heights (harris/versapod) the flat bag rider does not allow for easy fine tuning height. ... With the angled bag rider the bag can be slipped back and forth to fine adjust height.

Updated version of my previous Bag Rider. This one can be printed at 100% scale as it was exported in mm. ...

Updated version of my previous Bag Rider. ...This one can be printed at 100% scale as it was exported in mm.

hello, here is my adjustable bag rider for the KRG Bravo chassis it use the same mecanism as the cheekriser all you need is: - 2x8mm rod ( you have to cut to lenght) - 1xM5x25 screw ( from the Bravo chassis) - 1x flat nut ( from the Bravo chassis)...

A angular version of the bag rider for a GRS Bifrost riflestock. for a more "tacticool" look. ... Note: after some testing this works really well on bags, however it clashes somewhat with the sling if you do decide to use the push button sling swivel as...

Bag rider for the Ruger Precision Rimfire. ... This is a tight fit on the pic rail on the bottom of the buttstock, there is a hole in the side that can be threaded for an M3 screw to use as a lock pin

This is a front bag rider designed for a GRS Bifrost Stock. It mounts to the existing mounting points on the stock. I've made some changes from the first one I printed, the length had been increased and a hole added so that the sling swivel...

Bicycle rear bag attachment

Rear bag height adjuster for Protektor Bunny Ear Rear Bag w Hard Bottom 14A or similar size bags. These packing blocks interlock to give a firm base for the rear bag when the bag is not tall enough for the front rest. ...

A slightly longer version of the wombatordnance tikka bag rider

This is a wedge shaped bag rider to fit KRG XRay chassis. ...It uses the same holes and bolts supplied with the chassis to fit the picatinny rail to the rear of the stock.

Drawing based on my Aluminum MDT bag rider (fixed) but ported for m-lok mounting.

Helps raise the rear end slightly when using a fully extended 6-9" bipod with the ability to adjust the height by moving the rear bag forward/backwards. #### Hardware required: (2) M5 x 0.80 mm x 10mm button head/pan head screws #### Printer...

Solid and efficient Bag Rider Thanks for posting all make and any feedback is appreciated, ideas for evolutions, improvements...

The bag accessory from Ariel Rider attaches using parachute clips around the top tubes. It's a bit unstable. This platform clamps to the top tubes and provides a stable platform for the bag. The bag still attaches using the parachute clips, but...

This is an adapter plate for mounting a phone bag on a tomtom rider mount and using the power contacts to charge your phone.

This is an adapter plate for mounting a phone bag on a tomtom rider mount and using the power contacts to charge your phone.

Slider covers picatinny rail on the bottom of the stock so it slides on a rear bag. ... I use a rear bag with ears for F class.

This is a bag rider that I made for my MDT ACC stock. ... It fits in the MLok slot and attaches with 10-24 flat head hex drive screws and square nuts.

Angled bag rider for the KRG X-Ray rifle stock. Attached using the standard screws but gives a longer angled face. Print with the bag side down for a smoother finish. ...You might need some supports in the screw hole counterbores.

Angled bag rider for the KRG X-Ray rifle stock. Replaces the standard block using the standard mounting screws. ... Works better if it's printed bag face down as it is smoother, it might require some supports in the screw hole counterbores.