rear bike camera 3d models
168168 3d models found related to rear bike camera.youmagine
This only works on a rack with about an 11mm tube size and squared off rear support tube (touring style) - in my case I have a Topeak rack. ...This object adds to the angle of the tube to bring the total angle to about 20 degrees, which should match the...
thingiverse
This is an adaptor mount for a rear view camera that fits onto a bike rack (in lieu of the supplied seat post mount). ... Mount was designed to pick up the existing holes on my Axiom brand Bike rack (holes are 6.5mm at 45mm spacing if you need to drill...
youmagine
Print out, remove the support from the slide, test fit with the Fly6. It should be a little difficult to slide home so that it doesn't fly off but not really tight. I ALWAYS recommend secondary tethering of gadgets. You can do it on the Fly6 by...
thingiverse
I added an arm and a tube clamp to DaveStruve's universal Contour mount so that I could mount my Contour camera to my mountain bike facing backwards. It makes for some really cool videos when you're bombing down a section of trail with another rider...
thingiverse
This is a design I did for a friend with a Cycliq Fly 6 bike camera and rear light. She wanted a mount which didn't use velcro. Designed this up in Fusion 360. Printed in PLA but will probably do another one in Nylon or ASA if the PLA one shows...
thingiverse
This is a slide-in and clip holder for the TOOO rear bike camera. The mount fits around a 26MM post. ... I use the mount to hold the camera on the rear of my recumbent bike
thingiverse
The new version of the Fly6 rear bike camera from Cycliq (a great product!) is the Fly6[v] (as of September 2016) and it uses a simple velcro strap that is incompatible with previous Fly6 mounts. This is an awesome mounting solution for the back of a...
grabcad
This is a machined aluminum rear bike suspension triangle (turner).
myminifactory
Rear Bike Light, You'll need a rubber band to mount it on your bike. ... It should fit most bikes
pinshape
This is a rear view bicycle camera using affordable components that can be found on Amazon along with a simple 3d printable case along with clamps that will attach the units to your bike. Some concepts for the case style have been put together, but...
thingiverse
My wife wanted a rear basket on her bike, so I had to move the rear reflector. I`ve made a holder with a clip, so you can actually clip it on many places. The reflector itself is widely universal and maybe most of the bikes are having it. I`ve...
thingiverse
A tool used get grime off from between the sprockets on the rear cassette of bikes' gears. Very easy and fast to print. ...Here is one example how to use the toolhttp://www.youtube.com/watch?v=_nOEQI3DTts
myminifactory
this is an entry into the kitronik contest for the rear bike light. this is a self enclosed light that mounts to the seat post of a bike. if you purchase the Miniature DPDT Slide Switch from kitronick's website, there is a version of this that allows...
thingiverse
Based on Bike Kickstand V2, modified for rear mount. Easy to print and assemble, just 4parts: 1) Outer joint (print flat side down without support and >50% infill) 2) Leg (with support, >60% infill) 3) Bolt (no support) 4) Foot (no support,...
thingiverse
This is ESP8266 NodeMCU controlled 8 led NeoPixel ring rear bike light case. Part List: 1 x ESP8266 NodeMCU 1 x 750 mAh Li-po battery 1 x male-female battery connector 4 x M3 male-female Spacer Screw Nut 4 x M3 nut 4 x M3 screw for any...
thingiverse
This is a rear bike light holder for those types of lights shown in the pictures above. Because of its design, I had to buy another light when it got damaged. You should use supports for the ears. ...The grey one is an early version, before I've...