redcat lowrider mods 3d models
34123 3d models found related to redcat lowrider mods.thingiverse
Redcat Lowrider Mod Wheels come with 4 faces but only one set of barrels to use them in. Redcat has no plans to make barrels available so I made these totally unofficial barrels for all the RCers who want to use them on other cars. ...Take it, mod it,...
thingiverse
All the 3D printed parts that are needed for the build of a Epiquad lowrider.
thingiverse
This printable mod lets you alter your Makerbot Automated Build Platform to shrink it vertically by 11 millimeters by moving the motor to the rear. The parts are also laser cuttable. Benefits: Get more height out of your Makerbot builds Uses...
thingiverse
Custom wheel designed to fit these tires https://www.rcplanet.com/redcat-lowrider-low-profile-tires-w-foams-rer14654/p1356965
thingiverse
Linear bearing mount for 'SBR16-59.06 inch / 1500mm 16mm Linear Motion Rail Shaft Slide Guide 1Pcs + 2Pcs SBR16UU Linear Bearing Slide Slider Pillow Block' bought on Amazon. ... Custom belt clamps and mounts to keep alignment.
grabcad
I added a couple washers to the wheel bolts before this piece to keep the wheels from rubbing on in.(Note: I would recommend using something like a flat aluminum bar instead of an angled piece, because the angle interferes with the gantry on the...
thingiverse
With this mod, you move the upper shock mounts into the center of the car to give you a much better turn radius and a greater axle drop. After adding the mod, please move the steering link on the servo arm to get a better turn radius. I ended up...
grabcad
Para amantes da cultura lowriders, ideal para Impala, BelAir, MonteCarlo, entre outros oldskull cars.
cults3d
Chevi impala lowrider articulated printed in 0.1mm support needed tpu needed for the tire
cults3d
Here: Lowrider Seats: https://cults3d.com/en/3d-model/various/lowrider-seat-04may-s07 https://cults3d.com/en/3d-model/various/lowrider-seat-07aug-s11 https://cults3d.com/en/3d-model/various/lowrider-seat-12jun-s09-back-pixel3d Lowrider wheels:...
thingiverse
Hello. ...My mod for redcat gen8 axle for building 6x6. ...Good luck!
thingiverse
......http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: font_size = 10 message = LOWRIDER stick_width = 8 flat_bottom = 1 stick_thickness = 3 font_thickness = 6 Font = write/orbitron.dxf hole_radius = 3
thingiverse
Center mounted servo bracket for Redcat Gen8 Scout. I was too cheap to go with an aluminum one, so I worked this one up myself. Included are standard bumper height and raised bumper height models, pick your flavor! During installation, screws...
thingiverse
... [Original Mechanical Quick Grab Phone Stand](https://www.thingiverse.com/thing:3681512) Notes Original phone stand provided as published in .zip. Also published [Git Hub](https://github.com/NHiggs/3DPrint_Mechanical_Phone_Stand_Mod_Lowrider)
cgtrader
Redcat Everest Gen7 modded all components
cults3d
Redcat Everest Gen7 modded all components
thingiverse
**These axle housings use a Redcat Everest-10/GEN-7 internals** - **4-link** and **3-link with panhard** versions - **(4x) M3x35 bolts + original bolts from Redcat axles** - **10 deg. of caster** built-in for better steering and drag link clearance -...
thingiverse
lowrider modification of the original QAV210 frame kit from Lumenier. Top plate from the kit replaced ... front part of the original top plate to be used for the upper front deck. Other parts of the original frame used without any modifications...
thingiverse
For various reasons, not the least of which is the creation of R/C scale Halo Warthogs, one may wish to add steering control to the rear of a Redcat Racing Gen8. Here I'll attempt to illustrate two different methods of achieving this feat. ...
thingiverse
This is a mod. ...for the Y plate for the LowRider V2 to accept C-Beam Rail for a more rigid gantry.