redcat rc 3d models

These are clips for installing LEDs into the pre-drilled holes on the bumper. They keep the LED in position using the existing holes as mounting points. ...To secure them, use M3x6mm screws or 3.5x6 wood screws.

Keeps your cables from hanging and snagging, which also looks nicer.

With this mod, you move the upper shock mounts into the center of the car to give you a much better turn radius and a greater axle drop. After adding the mod, please move the steering link on the servo arm to get a better turn radius. I ended up...

This is a three-piece print that seamlessly integrates with your stock body. Simply cut out the pre-designed sections and bolt them together - a process that's been thoroughly tested on custom chassis models. Minor modifications might be necessary,...

Customized version of https://www.thingiverse.com/thing:4845166 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4845166

Thought it would be cool to modify a Gen7 Plow. I took the front bumper and mount off, then this bolt-on design slides onto the frame - just needs a nut and bolt to secure it. I put this thing through its paces, clearing half of my driveway with...

So, after I pulled the front axle a bit back and tilted it a bit up in the back to put less stress on the driveshaft the caster got terrible. So I designed a fix for this. Just replace the outer part on the front axle. No additional parts...

Front body mount upgrade available on Amazon: https://amzn.to/39WJZUO I reinforced the weak spot where the original cracked by removing one hole near the crossbar, aiming to enhance durability. ... This sturdy front body mount can withstand rough...

Got the starlight instruments focus motor and then had no way to mount the guide scope or reddot finder.

Assembled a DIY LED light from Harbor Freight using the lights and battery pack - Caution - LEDs burn out at 6v, opt for 3 AA or AAA batteries instead. This configuration works well with 6v 5mm LEDs as well.

Broke myn Kaiju upper front arm after 10 minutes of running. ...Whipped this up and it worked until I got new parts.

A prototype chassis I have been working on, lines up with the existing chassis plate. When you remove the chassis use the original plate to line up and drill the mounting holes. i Did this to save time trying to line them up in Tinkercad. ...and also...

Magnetic body mounts. I designed these to replace the standard body mount used to mount a normal poly body onto the Gen 8 chassis. They are made to fit rare earth magnets from harbor freight ...

I'm fed up with seeing kids recklessly smashing into trucks, flipping them over, and having batteries fly out everywhere...Problem solved! I'm still learning the ropes when it comes to 3D CAD design, so I'm counting on you guys to make it look sleek...

This skid is engineered to correct triangulation problems with lower links as specified by the manufacturer. There are two skids available: Skid Link Screws, which allow you to reuse the stock link mounting screws and require four 3x10mm screws to...

Remixed from the original because I seem to have a different kind of field rotation ring than the original author. This works by attaching to either the first or second ring of the rotator with a tight interference fit. While sizing was the biggest...

Inspired by RedcatRacing's Gen8 headlight adapter, I created a similar part for Gen7 bodies. Installation: Remove the headlight stickers. Lightly rough up the body surface the adapter will be glued to. Use CA glue to glue the adapter to the body.

So, after I pulled the front axle a bit back and tilted it a bit up in the back to put less stress on the driveshaft the caster got terrible. So I designed a fix for this. Just replace the outer part on the front axle. No additional parts needed.

Adpater to aftermarket front bumper. Designed to fit the this bumper: https://www.aliexpress.com/item/32882431832.html?spm=a2g0s.9042311.0.0.27424c4dZqGEY0 But can be also fit other bumpers. ...(See dimensions drawing) Features: + Rigid design + Easy...

I'm taking a stab at upgrading my trusty Everest with rear steer for the third time, and this round I'm using Fusion360 - a software that's still relatively new to me.

The human-designed 1/10 scale monster truck rim has been successfully created using Onshape's powerful design tools. The rim was brought to life in Sketchup, where it underwent a seamless translation into a printable format. ...With its intricate...

Inspired by RedcatRacing's Gen8 headlight adapter, I created a similar part for Gen7 bodies. Installation: 1. Remove the headlight stickers from your Gen7 body. 2. Lightly rough up the surface where the adapter will be attached to ensure a strong...

This is a remix of the Rock Smasher front bumper(thing = 3008797) just a stubby version 158mm wide. V2 is a flat top version. ... Requires 2x M3-10 screws.

this is a offset style knockoff that i made, you can reverse the print for the other side

RC Helicopter

RC-Thermikbremse

rc boat

RC Helicopter

RC MODEL

RC Robot