rei camp x chair 3d models
376277 3d models found related to rei camp x chair.thingiverse
This is a very rough initial version of an insert for the REI Co-op Camp X Cup holder There are two inserts for holding misc items. ... #REI
pinshape
This is a redesigned foot design for an REI camping chair. ...The original foot isn't designed to stand up, this one is much more stout and rigid and will support your weight without breaking.
thingiverse
The REI Flex-Lite camp chair (https://www.rei.com/product/877258/rei-co-op-flexlite-chair) is excellent, but with a few drawbacks: -No cupholder -A bit unstable. -The pointy feet sink into soft ground. The feet in this model are intended to...
thingiverse
Insert for mesh cup holder in REI Co-op Camp X Folding Chair. ...Holds many standard cup sizes.
prusaprinters
I purchased the REI Co-Op Camp Stool to use while I fly FPV Drones. It is lightweight and collapses down nicely for packing-in and packing-out of flight spots.</p><p>A combination of my body mass and soft ground caused the stock feet to sink...
thingiverse
Built to fit over REI Flex Light camp chair feet to prevent them from sinking into the ground. It may work with other chairs as well. ... Diameter of the opening is 23mm at a 50deg angle.
thingiverse
I do a lot of backpacking and have a lightweight camp chair (REI brand). The feet of the chair tend to sink into soft terrain. Print four of these and put them on the ends of the chair legs to provide a wider base for the feet to distribute weight...
thingiverse
This is a foot from one style of camping folding chair. ... Hopefully, someone can use this to fix their camping chairs.
thingiverse
Bracket for the seat corner of a commonplace folding camping chair. Two aluminum leg tubes bolt into the small holes, where they pivot. ...The longer tube that goes up the sides slides through the larger hole.
thingiverse
Replacement cup holder ring to fit my Coleman brand camping chair. Modeled from the unbroken cup holder in the other arm. ...I have been using this part for several years without any issues.
myminifactory
This is for your tri-pod camp chair. It is the plastic end cap that fits on leg. ... I printed this in TPU plastic, 218 degrees, 70 degree bed, 100% infill.
thingiverse
cheap camping chair pipe end caps so it won't keep poking the fabric. fits on pipes which 16 mm (diameter)..or you can scale it up or down. ...with brims 10% infill
grabcad
The third hand you need to keep the sun (and maybe the rain) off you while you lounge in your cozy camp chair. The holster clamps onto one of the poles of the backrest of the chair (I tested, and you can't even feel it). The body has four slots for...
thingiverse
Our portable camp chair kept sinking into the ground. These feet are 100mm in diameter. The opening for the chair leg is 14mm. There is a hole in the side brace to connect bungee cords or straps to in order to prevent the feet from falling off. The...
thingiverse
You know those cheap and sometimes not so cheap folding camp chairs? Well the leg base on my not so cheap chair snapped in half. Perfect candidate for printing! Designed using Autodesk Fusion 360 Print Settings Printer: ...
thingiverse
These are some feet I made for my camp chair. It came with the regular feet that sink right into soft ground and some really heavy rubber add-on feet that are nice and wide but insanely overkill. I made these as a happy medium. Trail tested on a...
thingiverse
A replacement part for those Chinese made folding chairs everyone seems to use now for camping. Was about to throw a broken one away then I got stubborn and thought I can fix that. so here it is. Some dimensions have been tweaked to further improve...
thingiverse
- Also see my [Camp Chair Cell Phone Holder](https://www.thingiverse.com/thing:4758021) for hanging on the other side of the chair. - This is a reimplementation of [ThePlanetMike's](https://www.thingiverse.com/theplanetmike/designs) [Zip Tie Cup...
prusaprinters
Oh well, problem solved. Also see my Camp Chair Cell Phone Holder for hanging on the other side of the chair. This is a reimplementation of ThePlanetMike's Zip Tie Cup Holder in Fusion 360 using parameters. </li> <li>The hanger design at the top is...
thingiverse
The first picture is the foot that came on the chair, barely enough to keep the chair from digging into soft ground if you didn't wiggle. The second picture is a basic support but I wanted something better so the third picture is what I came up...
thingiverse
Not sure on the brand of chair, but could not find exact replacement so whipped this thing up I am not a professional, did this in tinkercad, but seems to work well Uses all existing hardware from broken chair foot, just print the one part, i did...
thingiverse
My roommate requested I build something to hold his umbrella while he sits in his chair holding his tailgate location on campus. After 5 prototypes, this is the version I settled on. The holster clamps onto one of the poles of the backrest of the...
prusaprinters
Clips to hold folding camp chairs closed. ...Just clip to two of the chair legs and it should hold the chair closed so you can more easily carry it. FreeCAD file attached if you want to customize to fit your chair.
thingiverse
- Also see my [Camp Chair Cup Holder](https://www.thingiverse.com/thing:4758010) for hanging on the other side of the chair. - The hanger design at the top is obviously specific to this application. On request, I might be persuaded to implement...
prusaprinters
This holder is designed to hang on the side fabric of the wonderful Cascade Mountain Tech chair purchased from Sam's Club.Also see my Camp Chair Cup Holder for hanging on the other side of the chair.The hanger design at the top is obviously specific...
thingiverse
This is a replacement part for the front foot of a Coleman Camp Chair. There are two versions, one with and without bottom serrations. Serrations (present on original chair) may provide slightly more grip on the ground, but make printing slightly...