reloading 3d

holds 100 cartridges, hole for checking primer and letting powder fall through.

<p>To prevent spent primers jumping all over the place, you can insert these fillers into the slot of the ram of your RCBS press. ...Both have the same function, the T-shaped one comes out with the shell holder, the other one can stay in the ram while...

Personalized Version of Thingiverse.com's #260104! Created using Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=260104 Instructions Using these custom settings: Column diameter is precisely set at 12.192. Ten even columns...

I could not find a 100 count tray, so I designed one. This was my second design, and 1st - 1 day+ print. Since I have learned much more since this one, I am confident I could shave the time and still hold quality. The 6.5 CM is published at .473...

Hold onto your Hornady Bullet Comparator Basic Sets, including an additional one specifically designed for the 6.5mm caliber. Install a pegboard holder onto the pegboard before applying glue, ensuring proper alignment every time. ...Place it near the...

Customized version of https://www.thingiverse.com/thing:260104 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=260104

Really appreciate BexarArms sharing the f3d file for their build as I learned a lot from their design/process!I wanted to see if I could use up some of the empty space by packing in the brass holes a bit closer together and overall reducing the...

This worked out very well, although I did have to drop the main block down a little more than I wanted too, only because the print bed vs the tray were getting tight.

So like many I have a small powder scale like may others, and there is a pile of them at this size so instead of taking it in and out of the box all the time I've moved it onto the pegboard with everything else. I added a small shelf for a pan that...

This is for the Lee Breech Lock Challenger Press (also suitable for other Lee presses). I created this modification because the press is frequently used as a deprime only press, but it prevents spent primers from exiting the ram. Print Settings...

These are stand over funnels, the case slides in the hole, and sits flush with the table. Sies adjust for trimmed vs untrimmed cases. ... 9mm 223 308 300 blk Designed in Autodesk Fusion 360 I have been printing these on a monoprice voxel using...

Any version

Customized version of https://www.thingiverse.com/thing:260104 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=260104

I'm excited to share a fantastic die holder tray designed specifically for a slot wall. ...If you'd like to get creative, I've included the Fusion 360 file so you can easily customize it to your heart's content.

Tray for cartridges 38 or 357. Because other did not truely accept those cartrigdes with a rim. Présentoir pour le rechargement des cartouches de 38 ou 357 avec une juppe pour les revolver. ... J'ai fait ça car les autres présenttoirs ne sont pas...

Customized version of https://www.thingiverse.com/thing:4830571 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4830571

Thanks to tgd25! ... Customized Version Based on Thingverse's #260104 Designed Using Thingiverse's Customizer Tool - Explore the Full Range of Options: https://www.thingiverse.com/apps/customizer/run?thing_id=260104 Faster Print Times Guaranteed with...

This adapter is designed to fit snugly into the top of a Hornady powder throw tube, preventing gunpowder spills from occurring, even in situations where time is of the essence or messes are more likely to happen. There's already an existing version...

Shortened the whole thing by a bit so that there is clearance for the powder funnel I'm using to charge the cases.

A rougher surface and a 45-degree incline in the cylinder make printing significantly simpler!

Customized version of https://www.thingiverse.com/thing:4830571 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4830571

this is a relaoding tray made special for .380ACP / .380Auto / 9mm kurz / 9mm court, will work also with 9mm Para, 9x19, 9x17, 9x21, 9sx20 Ladebrett für die oben genannten Kaliber

A custom-made version of http://www.thingiverse.com/thing:260104 was crafted using the Customizer tool at http://www.thingiverse.com/apps/customizer/run?thing_id=260104. ...The specifications for this unique piece include a diameter of 11.60, a height...

Crafted specifically for ammunition ranging from 40S&W to 45 ACP, this tray boasts hole diameters of 0.480 inches.

Customized version of https://www.thingiverse.com/thing:260104 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=260104

Customized version of https://www.thingiverse.com/thing:4830571 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4830571

Customized version of https://www.thingiverse.com/thing:260104 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=260104

Customized version of https://www.thingiverse.com/thing:4830571 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4830571

Holder for precision adjustment of Hornady headspace gauges, accompanied by an Allen wrench. ...This fixture can be conveniently installed onto a pegboard or seamlessly integrated into the wall with a few strategic drill holes.

Customized version of https://www.thingiverse.com/thing:5397631 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5397631