reloading 3d models

This is an adapter for using LEE/etc style slide-in shell holders with an old Herter's press (3/4" base). While quick-change adapters exist, this design is simpler, more rigid, and lower-profile. The reduced height offset should obviate the need...

Personalized Version of Thingiverse.com's #260104! Created using Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=260104 Instructions Using these custom settings: Column diameter is precisely set at 12.192. Ten even columns...

This adapter is designed to fit snugly into the top of a Hornady powder throw tube, preventing gunpowder spills from occurring, even in situations where time is of the essence or messes are more likely to happen. There's already an existing version...

Compact accessory organizer featuring storage compartments specifically designed to securely house essential tools such as primer tubes, precision allan wrenches, and adjustable end wrenches required for seamless Hornady LNL AP setup and quick tool...

holds 100 cartridges, hole for checking primer and letting powder fall through.

I made this tray using fusion 360, similar to a 9mm tray i purchased on ebay a few years back. ... Overall Dimensions (about 6 inches square and 3/4 in high) 18mm Height 150mm Width 160 mm length (hanging hole and label side) hole dimension : ...

Hold onto your Hornady Bullet Comparator Basic Sets, including an additional one specifically designed for the 6.5mm caliber. Install a pegboard holder onto the pegboard before applying glue, ensuring proper alignment every time. ...Place it near the...

Customized version of https://www.thingiverse.com/thing:4830571 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4830571

Made specifically to fit in a standard 50-cal ammo can, this design prints in two easily assembled pieces. It securely holds up to 21 precision dies and either three or six shell plates designed for use with Hornady Lock-n-Load systems. Compatibility...

The Real Life Wunderwaffe DG-2 from Call of Duty: Zombies created by Andrew of The Ray Gun Project (YouTube). Watch this video to see all the features of this iconic prop: https://youtu.be/aU-9EFjIyJc Detailed Assembly...

This worked out very well, although I did have to drop the main block down a little more than I wanted too, only because the print bed vs the tray were getting tight.

I could not find a 100 count tray, so I designed one. This was my second design, and 1st - 1 day+ print. Since I have learned much more since this one, I am confident I could shave the time and still hold quality. The 6.5 CM is published at .473...

Holder for precision adjustment of Hornady headspace gauges, accompanied by an Allen wrench. ...This fixture can be conveniently installed onto a pegboard or seamlessly integrated into the wall with a few strategic drill holes.

Original part had components that did not lay completely flat on the printing bed. ... I just used 3D Builder's 'split' function to slice a plane off the bottom of the part.

Crafted specifically for ammunition ranging from 40S&W to 45 ACP, this tray boasts hole diameters of 0.480 inches.

This item serves as a substitute component specifically designed for the recharging mechanism of the Nerf Dart Tag Speedload 6.

Here is a simple design for a three-die storage box that can be printed at home. Since it was impossible to locate a suitable pre-made template online, this custom solution was created with functionality in mind. ...The resulting product is...

Customized version of https://www.thingiverse.com/thing:4830571 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4830571

I designed a custom holder for my dad, which features 30 expandable bullet trays. ...I also added a 12mm-high component with some minor adjustments to enhance its functionality.

Customized version of http://www.thingiverse.com/thing:1457037 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1457037 Instructions Using the following settings: Height is set to 1 Hole Slack is...

Thanks to tgd25! ... Customized Version Based on Thingverse's #260104 Designed Using Thingiverse's Customizer Tool - Explore the Full Range of Options: https://www.thingiverse.com/apps/customizer/run?thing_id=260104 Faster Print Times Guaranteed with...

<p>I had a hard time tapping a 223 catridge with 5/16 36tpi so i made this one with M6 .75 threads. This way i can tap my 223 with 5mm drill bit and M6 .75 tap.</p> <p>The pusher is a guitar string. Just glue the pusher head onto the guitar...

Really appreciate BexarArms sharing the f3d file for their build as I learned a lot from their design/process!I wanted to see if I could use up some of the empty space by packing in the brass holes a bit closer together and overall reducing the...

Ropin' Champion Practice Gear. Version Tailored from Thingiverse. Customized http://www.thingiverse.com/thing:260104 Made with Thingiverse's Customizer App. http://www.thingiverse.com/apps/customizer/run?thing_id=260104 ...

This die holder is a little beefier than others I've seen on Thingiverse. The shape is a bit more reinforced, and it holds 4 dies per piece (I find myself using 3-4 dies max for a specific cartridge). It has pilot holes for standard M4 bolts and a...

A custom-made version of http://www.thingiverse.com/thing:260104 was crafted using the Customizer tool at http://www.thingiverse.com/apps/customizer/run?thing_id=260104. ...The specifications for this unique piece include a diameter of 11.60, a height...