remix creator 3d models
179736 3d models found related to remix creator.thingiverse
I had significant difficulties printing the original item with ABS, as the layers would often separate at the male threads. Raising the print temperature to help with adhesion caused the threads to distort. So, I pulled the original item into...
thingiverse
Remix of Mr Kee's 1/4" shim for the Flashforge Creator Pro 2016, used when adding a 1/4" glass bed plate. ...It's modified to change the tabs that go over the name plate flange to make use of the existing screw holes that formerly fastened the...
thingiverse
This is a simple remix that allows the great source thing to be printed without supports, for the FlashForge Creator Max, to help center the filament feed closer to the center of the reel, which should help it to feed slightly better than the stock...
thingiverse
Customized version of https://www.thingiverse.com/thing:4321016 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4321016
thingiverse
Customized version of https://www.thingiverse.com/thing:4321016 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4321016
thingiverse
Customized version of https://www.thingiverse.com/thing:4321016 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4321016
thingiverse
Print Settings Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: .2 mm Infill: 80% Notes: Printed using Simplify 3D. ABS layer height .2 mm with infill at 80%... 4 shells and 4 top/bottom layers each (I like sturdy prints). Speed...
thingiverse
The problem was that it did not fit in the slot on the FlashForge Creator Pro because the bottom part of the 'cleat' was just a few mm too long. A quick trip through OpenSCAD and I took 3mm off it. ... Please edit in Customizer to fit your spool, by...
thingiverse
Remix of: http://www.thingiverse.com/thing:215739 This is for the Flashforge Creator Dual Extruder. I found that the arms were 2mm too thick preventing the heat sinks from going back on correctly and worse, preventing the arms from moving with...
thingiverse
... plate removed. Print Settings Printer: FlashForge Creator Pro Rafts: Doesn't Matter Supports: Yes Resolution: .15 mm Infill: 15 % Notes: Very few supports needed, only where the M3 nut openings are and under the pin that holds the blower fan on.
thingiverse
Remixed and resized a couple of cncartist's corner wire hide plugs to fit the newer flashforge creator pro.
thingiverse
This is a cooling fan duct design for a turbo fan. This is much better than the Flashforge duct as this one cools both hotends. Print Settings Printer: Flashfore ...
thingiverse
... a bit taller. Fits like a glove and printed with normal ABS. Gets the job done. Update: I also added a second version that has a slit for the raspberry pi camera ribbon cable. Print Settings Printer: Flashforge Creator Pro Rafts: No Supports: No
thingiverse
This remix only incorporates a small central rib in the air vents and main intake to the fan, to improve the manufacture without the use of internal supports in the parts not accessible. The placed support was made manually with the own program of...
thingiverse
Customized version of https://www.thingiverse.com/thing:4321016 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4321016
thingiverse
Great project by ThePizza (https://www.thingiverse.com/thing:4080588). ...I just modified code to render object with stronger rod-ball holder conntection
cults3d
I wanted rear mounted. I wanted a Blower Fan. I wanted both nozzles with part cooling. I wanted to be able to see the nozzles from the front. There wasn't anything just right so I made my own. PLA works fine but would be soft to touch while printing....
thingiverse
I wanted rear mounted. I wanted a Blower Fan. I wanted both nozzles with part cooling. I wanted to be able to see the nozzles from the front. There wasn't anything just right so I made my own. PLA works fine but would be soft to touch while...
thingiverse
The design was good, but the legs, printed vertically, is too weak so it broke. I just replaced them with 2 60mm m3 screws... ...add a little "horn-like" shape so it's easier to insert filament.
thingiverse
Customized version of http://www.thingiverse.com/thing:1733767 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1733767 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:1733767 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1733767
thingiverse
Customized version of http://www.thingiverse.com/thing:1733767 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1733767
thingiverse
Customized version of http://www.thingiverse.com/thing:1733767 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1733767 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:1733767 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1733767
thingiverse
Customized version of http://www.thingiverse.com/thing:1733767 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1733767
3docean
Terrible dinosaur legostyle all the detached separate you can collect other models of the designer in 3d editor includes formats obj,fbx,blend
thingiverse
My creator coin for my twitch fans (https://www.twitch.tv/teamz_co) hope you all enjoy it :)
myminifactory
This is a file generated by the Character Customizer (beta) of MyMiniFactory. ...Give it a try at the following link: www.myminifactory.com/character-creator/