remote controller holder 3d models

Customized version of https://www.thingiverse.com/thing:1818365 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1818365

Customized version of https://www.thingiverse.com/thing:1818365 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1818365

Customized version of https://www.thingiverse.com/thing:1818365 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1818365

I've also included a TV remote hanger in the design, but unfortunately, I glued it on and had to use rubber bands at the ends to prevent the remote from falling out. ... If I were to design a second version, I would definitely make sure to include a...

Because of their impressive wifi antennas, which double the range of connection between drone and controller, these components are quite heavy, requiring a sturdy additional holder to keep them secure. ...To utilize this setup effectively, you'll need...

Remix of Holder for X-Sense Remote Control RC01 Pro by MarkusK_I did not need the side part, so I removed it.

Remote control button blockers, for Samsung BN59-01315BAnd a version, without a blocker button, against tilting the remote control on the table.Print SettingsSupports:No Notes: Samsung BN59 01315B

I have three ES1008 remote controls, but only one came with a holder, so I designed this alternative myself. It fits perfectly and can be securely attached to the wall using double-sided tape. Print Settings Printer: ...

A wall holder for an X-Sense RC01 Pro remote control (for their connected smoke alarms). As a bonus it also stores the little tool that is used to open the battery cover. Just stick it to the wall with simple dual-sided tape. I also modified the...

Remote control button blockers, for Samsung BN59-01315BAnd a version, without a blocker button, against tilting the remote control on the table.Print SettingsSupports:No Notes: Samsung BN59 01315B 

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

We designed a lock specifically to prevent patio umbrellas from spinning wildly when tilted to block out the sun's rays. This ingenious solution is tailored for 37mm umbrella poles and should work seamlessly with sizes ranging from 36-38 millimeters,...

... compatible with the SMART PHILIPS remote control, but not tested. Printed holder for your WiZ WiZmote (for WiZ Connected Lights). Attach to any flat surface with double sided or use 2 screw Possible use for Philips Smart Remote Control (no testing)

Human: Personalized edition of http://www.thingiverse.com/thing:1238620 Crafted with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1238620 Settings Applied Applying Your Selections ...

Customized version of Thingiverse object #1238620 Created with Customizer! ...www.thingiverse.com/apps/customizer/run?thing_id=1238620 Instructions Using the following settings: Notch Clamp Size: 4 Clamp Width: 20 units...

This customizer has created a new design for http://www.thingiverse.com/thing:1238620 based on the following settings. These settings have been used to create this customized version: Settings used in creation: • Resolution ($fn) = 100 • Clamp...

Customized version of https://www.thingiverse.com/thing:1238620 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1238620

Customized Version of Thing #1238620 Created with Customizer! ... Instructions Using the Following Options: clampDepth is set to 3 $fn value is precisely adjusted to 100 width and height are accurately...

Customized version of https://www.thingiverse.com/thing:1238620 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1238620

Customized version of http://www.thingiverse.com/thing:1238620 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1238620 Instructions Using the following settings: Clamp notch enabled Depth set to 7 units Width set...

Customized version of https://www.thingiverse.com/thing:1238620 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1238620

Created with Thingiverse's Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=1238620\nMade to Order for Your Needs! Customization Instructions Ahead To Suit Your Preferences: Selecting Parameters: Length = 6.67...

Customized version of https://www.thingiverse.com/thing:1238620 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1238620