remote holder for wall 3d models
2437141 3d models found related to remote holder for wall.thingiverse
Holder for small remote control that came with an LED light. The holder can be fixed to the wall. Useful for not losing the little remote. Thought I would upload it in case anyone finds it useful for a similar remote. Approx. ...inner dimensions of...
thingiverse
Having several Tradfri bulbs replacing bulbs that were controlled by a wall switch was problematic because once the bulb was turned off with the wall switch, only the wall switch could turn it back on (the remote, the app become useless). This cover...
thingiverse
Holder for RC-X35 BOSE Lifestyle V35, V25, 235, 525, 535, and 135 Series I or II remote control. Printed lying flat, wall side down. Works just fine. Not much more to say... If this design put a smile on your face or solves a problem for you,...
thingiverse
I bought a Gree Air Conditioner but it had no holder for the remote control. ...So I decided to design this holder for wall.
cults3d
Holder for the Eurodomest #972080 remote control Eurodomest is a very cheap brand for KAKU interfaces on the Dutch Market. Their products are aimed at the Dutch market. The rest is in Dutch. De Eurodomest afstandsbediening en stekker schakeldozen...
thingiverse
Holder for the Eurodomest #972080 remote control Eurodomest is a very cheap brand for KAKU interfaces on the Dutch Market. Their products are aimed at the Dutch market. The rest is in Dutch. De Eurodomest afstandsbediening en stekker schakeldozen...
thingiverse
Nowadays things are remote controlled, so I decided to create a cover for this box with a holder for the early Hue Remotes. Added an archive file from Fusion 360. The design is parameterized (almost anything is available as parameters) so you can...
thingiverse
It's a wallholder for 3 remotecontrolls. ... two bigger ones on the back side an on the front a smaller one for an AppleTV Siri Remote. ... Hole sizes: 52mm x 26mm 38mm x 12 mm
thingiverse
PLA wall mount remote control holder. Screws into wall with 2 screws. ...Holds LED remote control.
thingiverse
Simple holder for TV and alike remotes for 2 things
thingiverse
A wall mount holder for three remote controls with additional storage space on top. ...The middle slot is slightly shorter for smaller remote controls such as those from the Amazon Fire Stick Can be printed without support.
thingiverse
Samsung TV holder for on the wall or similar. Use double-sided tape. ... Or use the .STL file with screw hole
thingiverse
Both remote holders fit both types of RGB-remotes, but they are optimized for getting the remotes easy in and out. The 44-key version is 55mm tall, the 28-key version just 35mm. I recommend printing it with the open side facing up. ...I included the...
thingiverse
Simple wall holder for remote controller of led dimmer
thingiverse
Wall holder suitable for an A/C remote control, so you can mount it at a convenient location. Dimensions can easily be changed, so you can adapt it for other remote controls. ...An optional chamfer will provide some rounding at the entry and bottom.
thingiverse
Changes/additions, FloKra 2022: - my model is designed specifically for a mumbi 27541 RC socket remote, but is fully customizable - chamfer not only on bottom and top-inside as in the original, but also on top-outside and on front cutout - position...
thingiverse
Features added: - mounting screw holes can be switch off for mounting with double sided tape - the corners of the cut-out section can be cut off (or not) to make inserting the remote easier - the detail of the render can be chosen. (higher quality...
prusaprinters
This is a simple model I made that allows the Apple TV 4th Gen remote to be mounted to a table, wall, or anywhere else you can think of! It has two countersunk m4 holes to allow it to be screwed to something. ...I personally use it with velcro command...
thingiverse
... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1818365 Instructions Using the following options: corner_r = 4 comp_h = 52 comp_d = 25 comp_w = 48 slot_lower = 16 chamfer = 0.6 tol = 0.25 wall = 2.5 slot_w = 36 mnt_dia = 2.5
thingiverse
... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1818365 Instructions Using the following options: corner_r = 4 comp_h = 52 comp_d = 18 comp_w = 46 slot_lower = 16 tol = 0.25 mnt_dia = 2.5 wall = 2.5 slot_w = 34 chamfer = 0.6
thingiverse
Customized version of https://www.thingiverse.com/thing:1818365 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1818365
thingiverse
Customized version of http://www.thingiverse.com/thing:1818365 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1818365
thingiverse
Customized version of https://www.thingiverse.com/thing:1818365 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1818365
thingiverse
Holder for a remote control for a bidet. it puts the remote in a more user friendly position and angle. The original holder just mounts flat to the wall. this holder puts it in a angle perpendicular to the viewpoint when sitting on the throne. It...
thingiverse
So I didn't see many (any?) remote control holders for 3 remotes, so I whipped one up in Fusion 360. It seems to hold any standard Sony, Samsung and LG remotes. Also holds the newer Comcast/Xfinity voice remotes. I think each slot has the perfect...