reolink camera mount 3d models
423900 3d models found related to reolink camera mount.thingiverse
I made two mounts for me Reolink bullet cameras. 30% infill 0.2 layer 4 walls 4 top and bottom designed for a 20mm gland for plastic 20mm pvc tubing Neatly fits all cables inside. I didnt make a seal for the lid as none of my cameras are...
thingiverse
I've used this with the Reolink RCL-812A and RCL-510Abut should work with any other model (or camera) with similar mounting plate. ... Note this file is SLIGHTLY larger than the one in the photo to give more room for mounting strips, it's also been...
thingiverse
pole mount adapter for Reolink B400 bullet-style camera also may work with other similar cameras like RLC-410 designed for about 2 in. dia. pole, but may work with other diameters. Uses two zip ties to secure in place. recommend printing in...
thingiverse
Basic arm camera mount for a Reolink e1 camera that hooks into the 2020 extrusion at th front of the build plate. This sits low enough that the build plate clears the arm when it all the way to the front. The top plate is designed to work with the...
thingiverse
Mounts for Reolink IP dome and bullet cameras over a single gang box. Was tested on rlc-520, rlc-520a, and rlc-410. Might fit others. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/h5bkyj1cxjH
thingiverse
This is Rev2 I need to test fit and adjust the model to be printable without supports but hey its free
thingiverse
This mount is customised for the Reolink B800 bullet camera but the concept would work for any camera where a strong mounting is needed in thin or soft sheet metal. The mount has three pillars to suit the (Reolink) supplied self tapping screws...
thingiverse
Reolink SolarPanel Camera Adapter The adapter makes it possible to connect the solar panel directly to the camera. ... Infill 25.0 Material: PETG Support Structure: Yes (Tree, Angle 40.0) plate down
thingiverse
I borrowed from DutchSwede design and changed the camera mounting holes for my Reolink Dome Camera. I also added the Reloink logo and a couple of different version with slight differences. I also changed the design so that there is no need for...
thingiverse
A great inexpensive camera that has Pan/ Tilt capability. I use them to watch my 3D printers and shut them off if anything is wrong or if they finish. ...I recently used them in the house to watch the cats while I'm away.
thingiverse
Wall mountable junction box for a Reolink RLC-410 or RLC-510 security camera. ... Easily modified for other cameras.
thingiverse
I upgraded from Arlo cameras to Reolink PoE after Arlo kept asking for more and more money. For the back of my house I decided to use a single Reolink Duo. I initially tried to mount it from the eve of my house, but the mount wasn't designed to work...
thingiverse
I used this to hide the wires inside a concrete wall which I chipped out with a chisel and hammer. ... I
prusaprinters
This model is a Reolink RLC-811A Camera Mount for 5" Dutchlap Vinyl Siding. ...It will print with no supports.I needed a sturdy mount for outdoor use so I printed with 4 perimeters and 4 top and bottom layers out of ASA.Mounting hardware:Camera to...
thingiverse
This hook was created for people like me who need to use the HeyVye project but to use it with a Reolink E1 Zoom camera. The file was printed at 60mm / s without supports using black PLA material. (The white attachment piece is the original...
thingiverse
**Variants** I've included two configurations: Model #1 - Mounting slots suitable for #10 screw diameter (0.19") - CAT6 Cable pass-through WITHOUT connector (0.25") Model #2 - Round mounting holes suitable for #10 screw diameter (0.19") - CAT6 Cable...
thingiverse
This design allows mounting a Reolink 410 camera directly onto a standard European wall box (for flush mounting). You will need three M4 screw nuts with 16 mm flat screws for attaching the camera to the plate as well as two countersunk screws to...
thingiverse
This is a simple camera holder for the Reolink E1 Pro and E1 Zoom model... Intention is to be able to clamp it on a vertical water pipe like in a storage room facility... ... Designed in FreeCAD 0.19.
thingiverse
... so that it would not be visible to the eyes too much. The wall mount requires a reolink camera mount or a printed alternative. (https://www.thingiverse.com/thing:5951978) Wall mounting holes are 5.1mm Reolink camera mount mounting holes are 4.1mm
thingiverse
Capuchons pour protéger le bouton Reset et l'alimentation optionnelle contre l'eau Le capuchon pour le connecteur ethernet : https://www.thingiverse.com/thing:4651149 Fichier FreeCAD joint --- Lid to protect Reset and extra Power connector on PoE...
thingiverse
Acessories for reolink 810A cameras: Inner reinforcement for reforce the bolt pattern, internally when installing on a derivation box. ...It used 7mm nuts cover - cover for the cable hole, if you don't use it
prusaprinters
A Simple adapter, to connect a camera (RLC-510WA) to a fenceI've used M3 screws, and brass hot melt Inserts to make it more strong, and adjustable.
thingiverse
This is a wall mount for the reolink NVR - Camera Recorder. ... Printen with white PETG, worked very well and looks great.
thingiverse
Built this mounting bracket for the ReoLink E1 Zoom. ...I'm not sure if it will work for other models of the ReoLink E1.
thingiverse
... or down. ... Left/Right is from the perspective of the camera. If you want the camera tilted up instead of down, choose the opposite left/right direction. ... Updated with more clearance for mounting screws By request added a version with a 45/20 tilt.
thingiverse
Remix to jan93's Reolink NVR wall mount. ...Just added holes for easier access to the mounting screw!
prusaprinters
Here is my design for Reolink E1 Wall mount.No supports required.Assembly:You will need 2 M3x6 screws to attach with the plate included with the camera to the main body. ...Cover plate is a snap in design.Wall mount via 2-4 screws.