replace psu fan 3d models

:) https://paypal.me/jpal85 Threw together a quick remake of my previous lrs-150 psu enclosure. This one uses a thinner/smaller C14-switch and my new xt60-clamps. The cover is press fit and has 1-2 screw holes as well. Uses this C14-switch (no...

... fit, making them easy to secure once in position. To get them exactly where they need to be, I screwed in a bolt first without the inlet part attached, and then added the rest of the components. As for the PSU cover, I left it unaltered and unused.

The Zaribo PSU Brace is designed for use with Zaribo printers that are housed within an enclosure, while the power supply unit resides outside. Its purpose is twofold: it not only provides additional structural support to the frame but also enhances...

this is a psu stop block modified fromt he oem version provided by [elegoo](http://69.195.111.207/tutorial-download/?t=FDM_Power_stop_block) to work with the wonderful mod made for the ender 3 by [teaching...

I was searching for a suitable bracket to accompany my Chinese import PSU PCB. Failing to find one that met my requirements, I decided to create my own from scratch. The design allows users to screw the bracket into place from the inside of a table...

Remixed from Mahooz part. ...This is a Ender 3 power supply parts so you change the fan. ...No supportr needed, prints in about 4 hours at 0.2mm

... in place. 4) to hold the cover in place screw the 10-15mm M3 screw through the hole on the right wall onto the hole on the PSU. I hope I made it clear. I'll try to answer questions. ... I'll leave an .STP file so you can modify if you wish to.

The PSU is a BeQuiet Power 7 300W model, but the mount should work with other PSUs of similar measurements: 86 x 150 x 140mm. Be sure to check the ventilation openings too - they're pretty important! This design should also work for other...

... like I did. The cover is made to be a press fit over the stock PSU cover, but you might need to sand it a little inside, or if it's too loose, you can make up the difference with short strips of something like painters tape. ...

... 4) To hold the cover in place, screw the 10-15mm M3 screw through the hole on the right wall onto the hole on the PSU. I hope this is clear. I'll answer questions if you have any. ... I'll leave an .STP file so you can modify it if you wish to.

Adapter replaced from failing Flyingbear PSU to high-powered NEWSTYLE 360W Power Supply Unit.

I rearranged the layout because I preferred placing the fan within the design rather than on its exterior. Purchased a fan from Aliexpress. ... https://nl.aliexpress.com/item/32861064814.html?spm=a2g0s.9042311.0.0.27424c4d2WkAeS If you appreciate my...

Rear fan: 80mm Upper fan: 130mm For the screen support part, I'm using this: https://www.thingiverse.com/thing:1721434 ------------------------------------------------------------------------- This thing was made with Tinkercad. ...Edit it online:...

i threw together this cover in an attempt to keep my SSR and PSU cooler under higher temp printing. I will update the file to hold heat inserts, but for now i plan on just running slightly longer bolts and a washer/nut under the cover.since this is...

To demonstrate fan-building fundamentals, this example will illustrate creating a simple cage and fan blades.

To replace my broken original stock cover from 2018. . - For an early model of Ender3 family. . ... - SupportBlock snap in under main box for preventing sag down.

Spacer for the backside of the power supply unit cover found on numerous printing devices. ...Raise the cover by 10 millimeters, enabling a 60x60x25-millimeter fan to be installed inside.

The wiring might be slightly tight, but it should not pose any major issues compared to other similar designs, like the one used for my stock 20A PSU. You will need three M4 screws to securely attach the cover to the power supply unit and two M3...

:) https://paypal.me/jpal85 Threw together a quick remake of my previous lrs-150 psu enclosure. This one uses a thinner/smaller C14-switch and my new xt60-clamps.<br/> The cover is press fit and has 1-2 screw holes as well.</p> <p>Uses this...

Here is my custom Tevo Tarantula PSU enclosure, which has room to mount a 240v Volt & Amp meter with a safe 3 pin power supply and fuse. This design was inspired by the 'Tevo Tarantula Control Box' linked below:...

I was looking for a nice bracket for my Chinese import PSU pcb. Couldn't find one, so made my own. You can screw the bracket from the inside on a table or something more heavy.<br/> I bought the board on Aliexpress:<br/> <a...

It then turned out that removing the PSU is quite cumbersome and that the holes in the LACK-"cardboard" are gradually tearing out.For this reason I have designed an alternative power supply suspension that allows the power supply to be detached from...

Float DC Ground on PSU Mod: https://www.youtube.com/watch?v=dnD-zaOznRo Recommended Supplies: 2x HP DPS-1200FB:...

:) https://paypal.me/jpal85 Part of my parametric modular electronics lab project. This PSU enclosure is meant to be mounted under the table. C14-plug/switch is the standard 3d-printer one that comes on most printers. Two XT60 as outputs. Search for...

And probably paint it with something to be really sure, although I doubt that the rest of the PSU is more than splashproof. I have the 120W version, but I'd guess all the rest are the same. Print Settings Printer: Zonestar D810 Rafts: No Supports:...

I'm building the FB2020 Printer and the 200W power supply I purchased doesn't fit the printed brackets in the design because my PSU is smaller. So, I went to TinkerCAD and designed this one. I haven't printed it out yet, so there may be alterations.

Covering up the Dell Power Supply Unit is a must when using it as a replacement power source for my Anker Advantage II AA23300 battery pack, which in turn powers my Q6 Pro Lithium Ion charger.

Sadly I found no design for a psu housing that fit my needs. So, taking the opportunity to learn how to 3d model, I decided to make my own. The keystone receptacle can be found [here](https://www.thingiverse.com/thing:4695995) on thingiverse....

Bases on "Old fan''. ...I do not found his link.

Fan for PCs or other small electric products cooling