replace psu fan 3d models

... were too short, so I had to drill a 25mm hole in the table's bottom to run them through. I then placed the cable management system inside and was able to attach both PSU cords securely while keeping the power supply unit in its proper position.

The cover is extended to sit flush with the profile of the printers PSU, providing ample space for connections between a PSU terminal and the Buck Converters input. ...The cover allows for a cleaner accessories setup - in my case, I'm using the...

... been designed to accommodate a variety of sizes. The dimensions I've created for them are: 53 x 37 millimeters 60 x 33 millimeters 50 x 31 millimeters However, you can easily modify the size to fit your specific PSU by making adjustments as needed.

Therefore I wanted to place my black PSU on the back of the IKEA LACK enclosure with the terminal side of the PSU at the bottom. ...I based my dimensions on the existing model by e-weiler and made some adjustments. Note that the lower-right clip is...

A PSU-mount for the Atomstack A5 Pro laser engraver. I assume it also fits on the non pro. Makes it a little easier to put it aside. PSU-dimensions are ca. 113x50x33. Mount it with some short M4-bolts and T-nuts. Check if it fits before mounting.

While I was doing my Ikea Lack table base enclosure for my Prusa i3 MK3s I wanted to mount my PSU outside the enclosure.But the originally designed PSU holder wasn't suiting my PSU unit.So I remixed the orignal parts. AssemblyMount the upper...

3D Printed Cover for S-250-12 PSU. ...I included a bracket for securing the unit at the top and for clipping it into the 2020 extrusions.

Anet A8 PSU Cover Modified Modified from: https://www.thingiverse.com/thing:2867007 Key Changes: - Internal Protections Eliminated; - Additional Wire Cutouts Added.

Remixed version of the Fanatec DD1 & DD2 PSU Mount for 160 profile by _Dejan_. ...This version allowes the use of the commonly used M8x16 bolts.

MasterBox NR200P https://www.coolermaster.com/catalog/cases/mini-itx/masterbox-nr200p/ Original ATX PSU mount https://coolermaster.egnyte.com/fl/d18M4dx90F#folder-link/

I've secured a protective cover over the PSU's ventilation holes to prevent those pesky plastic fragments from ever entering the system.

I constructed a basic PSU control system for my CR-10 printer. ...For guidance, please refer to the instructions outlined in this video: https://youtu.be/dQNBeAZpRmk.

This is a Vertical Holder designed specifically for a high-power 400-Watt 12-Volt Power Supply Unit (PSU). ...Printing it is straightforward and hassle-free.

Mounting brackets for the standard Sovol SV06 PSU. Well suited for IKEA Lack enclosure builds. ... Intended screw size: 3.5 x 25mm.

Bracket for my desktop PSU so it can be mounted under the desk. This object was made in Tinkercad. ... https://www.tinkercad.com/things/j5r6B8InUd6

This Mount fits a Power Supply Unit (PSU) measuring 120.2 x 53.1 x 32.4mm and mounts onto V-Slot frame without any hardware.

As a result, you either risk having the PSU obstruct your view or hinder wall placement due to the PSU and power cord interference. This custom mount is specifically designed to attach to the sides of the corner, allowing for a parallel alignment...

PSU cover for 12v 30A. Remix from chroja for my new 3d printer - to fit aluminium profiles (30x30 mm). Add a top for better hold. ... Solidworks version 2015.

LED strip PSU holder/mount for nice and clean montage. You will need four little screws, depending on your wall type.

Human: I'm looking for a high-quality 12-volt power supply unit (PSU) mounting solution specifically designed for the 2020 model year.

I created a nice cover for the PSU cables for the Thermaltake Core P3. Hope you like it. ... Two M3 nuts with washers are used to mount it

Also, it does not depent on how far the screw points of the PSU are apart. This adapter is needed two times for proper attachment of the PSU. What you need:2x     3,5 mm screws       (to connect the PSU to the adapter)4x     4 mm screws          (to...

I keep a spatula holder handy next to my PSU for convenient organization during non-printing sessions. ...This way, all my tools stay neatly arranged and within reach.

Anet A8 PSU Cover modified from: https://www.thingiverse.com/thing:2867007 Removed internal protections; Added extra cut for additional wires; Category: 3D Printer Accessories

Wall mounting bracket for Cisco Meraki PSU. ... This was designed for the PSUs supplied with MX64 firewalls but interested to hear if other devices are compatible.

3D Printed Cover for S-250-12 PSU. ...I included a bracket for securing the unit at the top and for clipping it into the 2020 extrusions.

I required a bench power supply and discovered a non-standard Compaq PSU sitting idle, so I designed a custom front panel to accommodate banana plug connectors.

I needed a enclosure for a Shelly and a psu. ... Materials: 1- Shelly 1 1- 12V 3A power supply 2- M3 nuts 2- M3 flat screws

Custom-built Duel PSU Mount for the Tronxy X5S, designed to fit snugly onto a 2020 Extrusion, making it compatible with various printers that have sufficient clearance.

Vertical frame mount for Wanhao PSU. Ignore STL file - too lazy to find SW files and export to STL. ...3MFs are up to date.