replicator 2 build volume 3d models
1090252 3d models found related to replicator 2 build volume.thingiverse
This is a solid "max" volume print for the Replicator+ done during testing before product release. Print is 290mm x 190mm x 160mm, took just under 200 hours to print, and weighs in around 20 lbs. Print was also done raftless. Highly doubt that any...
cults3d
Locks the Replicator 2 build plate firm to overcome the common problem of corners lifting which results in prints warping (... ...and that can cause extruder jams).
myminifactory
Locks the Replicator 2 build plate firm to overcome the common problem of corners lifting which results in prints warping (... ...and that can cause extruder jams).
thingiverse
Locks the Replicator 2 build plate firm to overcome the common problem of corners lifting which results in prints warping (... and that can cause extruder jams). Instructions Print each file twice to make 4 x build plate stabilizers (i.e. the .stl's...
thingiverse
This is a build profile for a makerbot replicator 2 using PLA with makerware 2.4.1. It uses 10% infill, 100 micron resolution, and has both rafts and supports. I tweaked the support material settings a bit on the profile shipped from makerbot because...
thingiverse
Practical upgrade for the Replicator 2, this one will improve the rigidity of your build platform - and hopefully improve the surface quality of your taller prints. The material is EVA Foam. You can buy sheets in a lot of places. I recommend 2 mm or...
thingiverse
Use this Thing to hold a dial gauge for levelling your replicator 2 build plate. I used this dial gauge http://www.amazon.co.uk/gp/product/B000LFYK0A/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1 and these 10x1mm magnets...
thingiverse
UPDATE: got a build plate waterjet from glass and it was one of two best upgrades to the Rep 2 and has had a substantial positive impact on my build experience. The other best is definitely this: http://www.thingiverse.com/thing:42250 ...
thingiverse
This a build plate leveller specifically designed for the MakerBot replicator 2
thingiverse
Makerbot Replicator 2 Replacement 3/16" Glass Build Plate Adaptor Based on and similar to the adaptor that comes with P3-D's glass build plates.http://www.p3-d.com/products/glass-build-plate
thingiverse
These are designed to be cut out either by hand or by CNC machine, bent (again either by hand or using a sheet metal brake), and then installed over the Replicator 2 build platform support arms.
thingiverse
Woodsmoke made a super cool build plate leveler, but it was a bit small for the Replicator 2, so I stretched it! From Woodsmoke's original thing: Larger and more complex parts require greater accuracy in 3d printer calibration, especially with regard...
thingiverse
a couple of weeks ago, our makerbot replicator 2 was returned from service with a broken build plate latch (see second photo). this didn't happen out of the blue, as this latch was already acting up before. the service firm assured us that they would...
thingiverse
I overheated my Replicator 2 aluminum heat sink one day and messed up my original fan mount. This one has a higher horizontal part to allow for more room for the spring loaded filament loaders, as well as holes to allow access to the fan mount...
thingiverse
Why not print a raft just once covering the entire build plate, permanently attached to the surface of my broken build plate? Then I could print anything and it would come right off. And it worked! Just clean your build plate and level it as well...
cults3d
Customizable Spring Footings for Replicator 2/2X Build Plate
thingiverse
You can use this as a tool to double check weather a part can be replicated or to demonstrate the Replicator's build volume. The actual build volume as stated on the site is incorrect as can be seen by a test in the makerware software, so this is...
pinshape
Print this giant tower in a single build volume on a Form 2! The 12 parts stack on each other to make a tower about one Skyler tall (roughly 6'4"). The pieces nest concentrically. ...For Form 2 users, just download the .form and hit print - no supports...
thingiverse
... the lack of spring footings. This simple upgrade fixes this problem. UPDATE (Nov 14, 2013) Now customizable! Instructions Print three, unscrew the Replicator 2/2X build plate, install under each spring and re-install build plate and re-level.
prusaprinters
To enable the Heated Build Plate setting in the MakerBot Print software. You have to replace one file. First make a backup of the current "replicator2.json" (just zip it). And then replace the "replicator2.json" file. Win: C:\Program...
thingiverse
Yet another practical upgrade for the Replicator 2, this one will improve the rigidity of your build platform - and hopefully improve the surface quality of your taller prints. Only a few days after I got my Replicator 2 I began to notice that the...
thingiverse
After heating my build plate I use a feeler gauge to set my nozzle height to .006" above the rear most leveling screw, set my indicator to zero, and level the front to screws in relation to the back most. With this block I can consistently get...
thingiverse
To enable the Heated Build Plate setting in the MakerBot Print software. You have to replace one file. First make a backup of the current "replicator2.json" (just zip it). And then replace the "replicator2.json" file. ... Win: C:\Program...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=129663 Instructions Using the following options: inner_height = 8 base_height = 2 base_diameter = 12 inner_diameter = 6 hole_diameter = 3.4
myminifactory
Our build plate uses the whole build volume of your Replicator 2 or 2X, the plate is bigger than the original 2X HBP and so you have a more stable temperature at the side areas.The plate is "plug & print", that means you have not to solder or so. ....
thingiverse
IDE heated glass build plate system for the MakerBot Replicator 2 & 2X Compatibility: The IDE HBP System is compatible with every MakerBot Replicator 2 and Replicator 2X. You have to do no modifications on your device. What are the benefits? If you...
thingiverse
... and 25% infill, it would take a theoretical 73.5 hours and 274 meters of filament. How I Designed This I designed it by taking a hull of 3 circles, and systematically changing the diameter and spacing to match the build volume as close as possible.
thingiverse
for updates, use the version at https://github.com/dyanawu/openscad-buildbox use in your OpenSCAD and call placegrid() with the following parameters: vol: a 3-vector of build volume [x, y, z] origin: a 2-vector of your origin point grid: grid...
thingiverse
As centimetre values have little meaning to laypeople, I tried to print the biggest possible volume as economically as possible. The result is also remarkably sturdy. 19 x 19 x 11 cm Instructions All walls are 2 mm. Be sure to check perimeter width...