replicator 2x 3d models
45141 3d models found related to replicator 2x.thingiverse
Custom MakerBot door handle for the Replicator 2x. ...Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2X Supports: Yes Resolution: .2 Infill: 10% Post-Printing tap holes when done and use existing bolts to mount Instructions
thingiverse
The tubes always seem to fall out of our replicator 2x. ...This holder keeps the tubes from moving. I made mine say CBU engineering but the file says replicator 2x or has nothing
thingiverse
... snaps. This is the first 3d printed part that I have designed. Version 1.0 Instructions Printed on Replicator 2X, using Makerware medium setting (ABS). ...For best results, print 2 or more at a time so that the plastic cools between each layer.
thingiverse
... ...Printed with support. 4 springs of diameter 13mm/±33mm length needed I printed in ABS & smootth the surface of the feet with some acetone Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2X Rafts: Doesn't Matter Supports: Yes
pinshape
This is a carbon filter fume extractor made for the replicator 2x I manly use it to eliminate the smell from abs plastic. ...The fan that drives this system is an old cpap machine that I managed to fix high flow with low noise. Every thing prints...
thingiverse
Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2X Rafts: No Supports: No Resolution: 0.2 Infill: 100% Notes: I use 100% infill because they need to be strong if you intend to hang anything with much weight on them. ...Depending on...
thingiverse
Indicator holder for Replicator 2X Instructions Print the file as downloaded. Install indicator onto holder. Uses an M4 x 20 SHCS and a M4 nut that installs into a nut well for holding lug back indicator to holder. Clip holder on right side of...
thingiverse
Tool holder for the sides of a Replicator 2X, they will probably work a 2 as well. They are designed to hang between the side wall (wood) and the steel frame, there is typically enough room in there for them to slip into. You can use as many as tools...
cults3d
This is essentially the same design as my popular Replicator 2 Mk8 extruder upgrade its just been adjusted to fit the geometry of the Replicator 2X - so the instructions are basically the same. You will just need to use one of the long countersunk 3M...
thingiverse
This is a cover for the back of the replicator 2x under the clear dome. This is meant only to help enclose the print area and hold in heat and pollution in conjunction with a filtration system. Instructions I printed this on a 2x with ABS .2 mm...
youmagine
This is an extrusion cooling fan mount for a MakerBot Replicator 2X. It requires a blower fan such as the one found on the Replciator 2. This works a bit too well - it can push so much air across hot plastic that it can distort the plastic. Also...
thingiverse
This is essentially the same design as my popular Replicator 2 Mk8 extruder upgrade http://www.thingiverse.com/thing:42250 its just been adjusted to fit the geometry of the Replicator 2X - so the instructions are basically the same. You will just...
thingiverse
This is the left hand bearing block for a Replicator 2X. Mine wore out where the pulley shaft meets the block, so I decided to print one on my Taz 6 The slip bearings are held in place with a rubber O-Ring. I will be adding a retainer plate to both...
thingiverse
Since the weather of Taipei is humid, filament spools on the back of Replicator 2X would absorb enough moisture to affect the filament quality really quick. To keep the print quality of filament, I designed this spool system to protect filament...
thingiverse
This is a tool for the Replicator 2x. You use it with a Dial Indicator, I used a analog one. When you shall use it then you must start the leveling script on the replicator in the menu. Then cancel it after the first position. Then you got the build...
thingiverse
This thing was designed to allow the perspex hood of my Replicator 2X to be raised on a hinge - making it very easy to access the top of the machine without having to lift off the hood. Instructions I started by cutting 4 strips of 18mm plywood -...
thingiverse
With the combination of stock firmware and Makerbot Desktop, the cooling fan is controlled manually with the on-board menu on the Replicator 2X. I just wait until the first layer or two is down, then manually turn the fan on and leave it on. I'm...
thingiverse
Replicator 2X 80mm Fan Mounter For faster print, set 0.3mm layer
thingiverse
double filament guide for Makerbot replicator 2x. ... Use zip-tie to fasten to sheathed cable.
thingiverse
This will work with the Matterhacker spools and fits on the Makerbot Replicator 2X.
myminifactory
This alignment jig will help you properly align and level the nozzles in your MakerBot Replicator 2X 3D printer.
cults3d
This alignment jig will help you properly align and level the nozzles in your MakerBot Replicator 2X 3D printer.
thingiverse
Based on my research and trending ideas on kickstarter, these are things I believe need to be done to this machine to keep it competitive for at least 2 years: -Some sort of integration with makerware to allow for full replicator 2x functionality. ...
thingiverse
Tennisball feet for replicator 2x. Reduces Vibration (and noise) with ø66mm tennis balls. ... My print settings: PLA, 0.2mm, "upside down" with support
thingiverse
edited tool holder to fit side screws of replicator 2x Instructions 20% infill 2 shells 0.2mm layer height printed with blue PLA (glow in the dark)
thingiverse
... out plastic rivets that hold the two side windows in on a replicator 2X, not sure if the replicator 2 has the holes to fit these or not. ...Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2X Rafts: Yes Supports: No Post-Printing
thingiverse
This alignment jig will help you properly align and level the nozzles in your MakerBot Replicator 2X 3D printer. ...Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2 Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 10%
thingiverse
This Foscam FI8918 IPCam mount is designed for a Replicator 2x but will fit any M6 machine screw. ...You need to use the top half of the original mount that comes with the device.