replicator dual 3d models
53907 3d models found related to replicator dual.thingiverse
This is a model of a 3D printer based off the MakerBot Replicator Dual. ...The model measures: 169x137x122 mm (WxLxH).
youmagine
... 2 Mount for the replistruder. ... It allows you to mount a Replistruder to a Makerbot Replicator Dual 3d Printer. It should be straightforward to attach a replistruder - the instructions are much the same as those for the Replicator 2 mount. ...
thingiverse
0.2 mm layers enable support ('doRaft' = true) Installation on the Replicator (Dual) The guide attaches to the filament tubes that are attached to the rear wall via the plastic clamps. Unclamp the two tubes. Slide the whole guide behind the...
cults3d
Quick'n dirty fan mount for the Replicator Dual. Designed for a 40mm fan (the opening is 40.4mm side to side). The long plates (bottom and back) are 1.5mm thick the thickness for other ones (fan casing) is 1.2mm. Unfortunatelly, the walls are...
thingiverse
Quick'n dirty fan mount for the Replicator Dual. Designed for a 40mm fan (the opening is 40.4mm side to side). The long plates (bottom and back) are 1.5mm thick the thickness for other ones (fan casing) is 1.2mm. Unfortunatelly, the walls are...
thingiverse
Based on Replicator 2 upgrade i have built similar upgrade to fit the Replicator (Dual) or Called CTC Printer . you will need to download and print all the files EXCEPT Replicator Dual UpgradeLeft & Right.stl it is just for overall Look . you will...
cults3d
I used (http://www.thingiverse.com/thing:104796) as inspiration for a set of adjustable feet that fit the strange bottom corners of my ctc replicator dual Due to the strange and quirky design of the case or just the cheap production not a single...
thingiverse
I used (http://www.thingiverse.com/thing:104796) as inspiration for a set of adjustable feet that fit the strange bottom corners of my ctc replicator dual Due to the strange and quirky design of the case or just the cheap production not a single...
thingiverse
Cable chain for Replicator Dual Xmotor. To stop cable damage (repaired once already). 16mm x 12mm triangular internal hole. about 60mm diameter turn. Self supporting and sits flat. Sketchup model is in warehouse. Video of chain in...
thingiverse
This filament guide replaces the original clips on a Replicator dual (mine is a CTC model based on the FlashForge design). Its purpose is to feed the filament from the centre of the reel to help avoid tangles and the reel jamming against the side of...
thingiverse
I have a CTC Replicator Dual with a 225x145mm heated bed. I'm printing on a piece of mirror that I bought from my local hardware store for $20 AUD. (The mirror was 300mm wide, by 1.2m long, and I cut the mirror up with a glass cutter). So many...
thingiverse
I have a CTC Replicator Dual with a 225x145mm heated bed. I'm printing on a piece of mirror that I bought from my local hardware store for $20 AUD. (The mirror was 300mm wide, by 1.2m long, and I cut the mirror up with a glass cutter). So many...
cults3d
I have a CTC Replicator Dual with a 225x145mm heated bed. I'm printing on a piece of mirror that I bought from my local hardware store for $20 AUD. (The mirror was 300mm wide, by 1.2m long, and I cut the mirror up with a glass cutter). So many...
cults3d
I have a CTC Replicator Dual with a 225x145mm heated bed. I'm printing on a piece of mirror that I bought from my local hardware store for $20 AUD. (The mirror was 300mm wide, by 1.2m long, and I cut the mirror up with a glass cutter). So many...
thingiverse
5mm bearing plate files: Rep1 Right Plate 5mm.stl (Use for a single Replicator, or right side) Rep1 Left Plate 5mm.stl (Use for the left side of a Replicator Dual) To use the .scad file, download these files and put them into any folder together when...
cults3d
the screw thread and the locking ring are a fixed size for the CTC replicator dual 3D Printer spool holes. I have just recieved a different size spool of abs with a 29mm hole in the middle and it did not fit any of my spool holders so.... redesign...
thingiverse
the screw thread and the locking ring are a fixed size for the CTC replicator dual 3D Printer spool holes. I have just recieved a different size spool of abs with a 29mm hole in the middle and it did not fit any of my spool holders so.... the...
thingiverse
Pen adapter to fit the carriage of a Replicator Dual (or clone) in place of the extruders. Can take 2 pens or pencils for ditto drawing. Post-Printing Instructions Fit a pen or pencil into the holder using one of the spare bolts that came with the...
thingiverse
This is the makerbot spring-loaded extruder, but customised to fit the CTC Replicator Dual Printer. It uses the Gear of the original extruder. I also made the bearing fixed with a screw because the original plastic piece looked way to weak.The...
thingiverse
For those of you that like me didn't like what was out there to handle flexible filaments, this extruder designed for the CTC replicator dual it's a solid sturdier block that support the filament all the way to the hot end. (will allow you to adjust...
thingiverse
I recently blew out both extruder motor stepper drives on my Makerbot Replicator Dual Stepstruder. I won't go into the reasons why but wanted to show my repair. I don't think Makerbot sells parts for this unit (at least doesn't show them on their web...
thingiverse
Fan duct to fit a dual head Replicator to stop the fans from blowing air on to the job as it prints. In my experience this duct reduces the chances of large structural parts de-laminating, warping, bending etc as they print. ...
thingiverse
Clip-on filament guide to mount on the top of a Makerbot/CTC Replicator. ...It is design to clip on, and stay on, hence can be a snug fit.
thingiverse
] --- EN --- The Makerbot Replicator 2 Dual, review with care, by MrProto. The source files provided by Makerbot are filled with hidden defects (deliberately?). Here is a revisited version also allows you to use standard parts, easily accessible. Les...
thingiverse
CTC Bezer Replicator Dual nozzle fan support ver4, low profile
thingiverse
Use a BMG extruder and V6 hotend on your CTC Bizer, Replicator Dual or Flashforge Creator
thingiverse
This is just a simple door holder for any replica of a makerbot replicator dual/flashforge/QIDI tech