reprap dual extruder 3d models

Haven't got the extruder mounts figured out yet. Stay tuned. ...Print Settings Rafts: Doesn't Matter Supports: ...

Um die Extruder vor dem Luftstrom der Filamentlüfter zu schützen (Schwierigkeit die Endtemperatur zu erreichen), schlägt RepRap ein Klebestreifen vor. Da sich dieser immer löste, habe ich aus FR4-Leiterplattenmaterial ein kleines Blech angebaut. ...Das...

this is a extruder for my reprpap cube 3d printer. http://www.thingiverse.com/thing:13954 it consists of a central slider and carries two hexagon hotends. there are two 25mm fans for the hotend cooling and two 40mm fans with fan duct for the...

Ultimaker main board, will change to Rumba soon dual DD2 extruders, direct driving dual metal hotends E3D with cooling fans,Fast heat up lcd controller use prontface,cura or other opensource software 1.75mm ABS or PLA filament Fast change filament...

My primary goal was to be able to use the itty bitty dual flex extruder. Can be adjusted to any other X-Carriage hole spacing. The default is 23mm center to center for all four holes, which matches the Wilson TS, Wilson II, and Prusa i3 rework...

If you are making a dual extruder you will need to find a source for an additional set of these parts. Print the extruders. I have tested ABS and PET for suitable flexibility, but cannot vouch for PLA being suitable...although it should be okay. I...

I made this clamp to load/unload from my Reprap Bulldog Extruder. ...Just slide it over and the clamp will hold open the extruder.

Reprap Syringe Extruder NEMA17 T8 Screw 20ml syringe 3Dprinter Wolfy at http://www.thingiverse.com/thing:521949 Video http://v.youku.com/v_show/id_XODIzMjk5MDEy.html Reprap http://www.reprap.org/wiki/SyringeExtruder Learn...

... in particular, the idea of using a lever to trap the filament against its drive. Instructions The full Bill of Materials and detailed construction instructions are on the RepRap Wiki here: http://reprap.org/wiki/RepRap_Universal_Mini_Extruder.

However,  when I printed all the parts for the Reprap extruder and assembled it all ready to try I found that the filament could not get past the hole following the drive spline. It was 3mm out of alignment. So I realigned that and after 2 more...

I had problems with the heater holding its temperature so I made this so that the extruder would be able to retain its heat better.

This is the extruder body with break-away support. ... Instructions Print at 0.35/0.5mm and 0.2-0.3 layer height, the support should snap off with a pair of pliers.

Additional: rise X-axis current to 1000mA (oryginal 800mA) in config file on SD card or use lower speed mount extrude motor with connector pointed up What you get: Much higher objects quality (limited stringing) Faster/easier filament load (75mm...

Instructions Buy some M3x16mm caps, washers and plain nuts Separate the extruder drive from its motor From the bottom of the two bolts that the filament enters between remve the washers. They stop the extruder drive from sitting flat Discard the...

This one is very small, slides on the bolts of the extruder's resistence arm, and floats so it can move a little if needed. This worked great with the least amount of resistence. It only takes a few minutes to print it and try one. ...

This little plate will let you mount a RepRap extruder to your MakerBot. File updated: fixed back line segment. Instructions It's pretty simple. ... Cut it out and bolt it up.

This part will allow you to mount non-standard extruders to a RepRap Mendel. The pictures show an MBE-v9 by QU-BD but the goal of this part is to enable the mounting of any Makerbot style extruder. You can mount any Thing-O-Matic or Cupcake...

Again, the parts from the original direct drive can be re-used, but if you are making for anything other than a Fabrikator or are making a dual extruder, then you will need to source the following parts for each extruder; 13mm OD 5mm ID bearing with...

Probably only useful for owners of the following design (or similar):http://www.think3dprint3d.com/Kossel-Mini-3dPrinter-Kit The Kossel mini kit I got from Think 3d Print 3d uses a RepRap Pro mini extruder on one upright beam with a feed from a...

This is a support for dual extruders.

A customized gear for the new Reprap Ormerod. I thought of only using 5 ponies, but 7 is 28.57% Cooler. This gear feels plenty strong. Instructions I printed it 0.15 layer height and solid fill. I...

I had some heat issues with my (PLA) extruder and X-carriage, a M3 threaded rod melted through which I used to mount my hotend. I decided I needed some active cooling before I printed a new X-carriage and Extruder in ABS. So I designed a simple...

Pen holder designed to be mounted in one of the spare extruder mounts on the RepRapPro Mendel. Can be used to hold a pen for general purpose plotting or in my case PCB plotting. Instructions...

Its a mount for dual extruder for left hand and right hand MK8 extruders.

I designed this custom extruder based off a model I found on thingiverse that I tried and didnt work for me. ...if you have any questions about specific parts I used or if you want to get the 3d files please let me know in the comments.

Top: 2x Nema 17 42BYGHW811 2x Springs 20x7,5mm 2x MK8 Extruder 5mm 2x Bearing 6x19x6mm 6x threaded rod M5x85mm 1x threaded rod M6x85mm 2x Nut M5 5x Nut M6 (drilled) used as Bearing 12x Self-locking Nuts M5 4x Self-locking Nuts M6 2x Socket Head Screw...

LED ring light for car 80mm, for extruder RepRap BCN3D + To illuminate while creating the pieces, the screws sejección fan layer RepRap BCN3D +

This adapter is made for using a Wade-Greg-style extruder with an old RepRap Mendel 3D printer. ...

This is a bracket for upgrading the hot end/extruder on a RepRap printer to the E3D V6 hot end and the Bowden style Extruder. ... A full instuctable is at: http://www.instructables.com/id/3D-Printer-ExtruderHot-End-Upgrade/

This is a bracket for upgrading the hot end/extruder on a RepRap printer to the E3D V6 hot end and the Bowden style Extruder. ... A full instuctable is at: http://www.instructables.com/id/3D-Printer-ExtruderHot-End-Upgrade/