reprap guru 3d models
15444 3d models found related to reprap guru.
thingiverse
Wasn't happy with many available for the RepRap Guru i3 printer so I made my own from scratch. ... Supports: Yes (for the underside of the guide oval.) Material: PLA or PETG for more strength
thingiverse
... with the wire guard on. ... I also needed a guide for the wires so they would stop falling under the x-axis motor, getting caught and ruing the print. Thus I designed these to fit my Reprap Guru Prusa i3 V2 and increase the longevity of my printer.
thingiverse
Fan for the RepRap Guru Prusa I3 I braced the fan with two zip-ties. ...
thingiverse
Preliminary design to replace a RepRap Guru DIY Prusa i3 V2 3D Printer Kit's bed bearing holder that is cracked (picture is original with crack). It hasn't been printed yet. ... I have included the fusion 360 file in case modification is necessary.
thingiverse
This is a mounting bracket for a Reprap Guru Prusa I3. The rails are designed to fit with https://www.thingiverse.com/thing:905368. ... Sorry, my pictures seem to be randomly rotated.
thingiverse
Used these on my RepRap Guru to keep the X axis rods from sliding and rotating. May have to clean the holes up with a 3mm drill. Made to use a 3mm bolt and nut. a 6/32 set screw can be used for the variants that are made for it. ...- can just...
thingiverse
I had problems with the heater holding its temperature so I made this so that the extruder would be able to retain its heat better.
thingiverse
Brackets for preventing the z axis nut from escaping the x axis assembly on the RepRap Guru 3d printer. ... Pop the left bracket on from the right side and the right bracket from the back as shown in the pictures.
grabcad
Fan shroud and holder for Reprap Guru Prusa i3 V1 3D printer. Built in two pieces: holder for attaching to extruder body, glued to 40mm fan shroud. ...Designed on FreeCAD and printed with PLAThank you to Sergey Efremov for his rendering of the extruder...
thingiverse
spool holder for the RepRap Guru DIY Prusa i3 V2. The one that comes with it works but is kind of wobbly Sits on top of the frame. ... Mirror the upright to get each side of the vertical support 3 different sizes of spool centers Use the...
thingiverse
After trying out a few different designs i found, none seemed to take in account for filament changing. I designed these to make changing out filament easier as well as being able to move them completely out of the way if you have to work on the...
thingiverse
This is my first model, I've printed a variety of things before, but I've never designed my own model. ...I wanted a PSU cover with a spot for an IEC320 fused switch to increase the safety of my printer.
thingiverse
This is for the RepRapGuru printer, which is a knock off of the Prusa i3 v2, or the Anet A8. Includes hot end bracket, x0 bracket, a bracket that is mounted over the arduino Uno, a special chain link, and the standard chain links that others have...
thingiverse
Stiffer Frame!!! Awesome upgrade to the RepRapGuru This part replaced the Y-bracket. I over tightened mine in order to make the frame stiffer. I have beefed up the bracket. So now you can tighten the long 8mm rods that run up and down the Y axis...
thingiverse
I broke the spool holder that came with my printer, and couldn't find a replacement that was both simple to print, and fit my printer. So I designed this one. ...
thingiverse
Greetings! I wanted to upgrade the leadscrew on my reprapguru prusa clone to an actual lead screw and not the threaded rod that comes with it. These mounts allow you to use the upgraded x-carriages available elsewhere (I personally used this one...
thingiverse
Made this for a friend, which works with the X carriage found on his Reprap Guru Prusa i3 V1 3D printer.
thingiverse
This is a cap to replase the acrylic one that comes with the DIY kit and dosent address the fact that the bearings pop out of the top acryilic support (and the noise they make is driving me nuts) Thanks to Phil_Maddox for the idea. I added the...
thingiverse
File I made for the RepRapGuru Prusa i3 V2 to replace the four acrylic pieces that go next to the two Z motors. I didn't like how the motors were sort of "floating" and weren't on the ground. This made my printer lean forward at an angle. To solve...
thingiverse
Customized version of http://www.thingiverse.com/thing:280974 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=280974 Instructions Using the following options:...
thingiverse
This is the scepter of guru guro it is possible to assemble it in several parts
thingiverse
Customized version of http://www.thingiverse.com/thing:117519 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=117519
thingiverse
Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130
thingiverse
Customized version of http://www.thingiverse.com/thing:351996 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=351996 Instructions Using the following options:...
thingiverse
Guru-Guru was extracted from the N64 game "Zelda Ocarina of Time" and the musical note is a remix of ekul3e3's Treble earrings. Everything else was from scratch. The model has been repaired and remixed a tad to allow better printing. ...Please let me...