reprap huxley kit 3d models

Reprap Huxley Parts all ready to print on a huxley sized print bed!

Microswitch z-probe assembly for RepRap Huxley. The probe has been designed to probe a point very close to the Huxley's nozzle, allowing the full bed to be probed. ...Full assembly instructions on [here](http://jweoblog.com/?p=945) Video of probe in...

Brackets to mount two pieces of 8mm LED-strip on your RepRap Huxley (and probably other similar RepRap's). As the LED-strip is rated for 12V and Huxley use 18V i used 2 pieces and connected them in series, that means they run at 9V each and shines a...

Brackets to mount two pieces of 8mm LED-strip on your RepRap Huxley (and probably other similar RepRap's). As the LED-strip is rated for 12V and Huxley use 18V i used 2 pieces and connected them in series, that means they run at 9V each and shines a...

This is a cooling duct to be used with Reprap Huxley. The Huxley is very small and compact, this makes it quite hard to place cooling fans. This "Hose cooling" will take care of the cooling problem. You will need a strong fan/air pump. I use an air...

Instructions Edit the solidworks file to fit fan dimensions and print or just print STL Screw fan onto mount with two M3 machine screws and nuts Screw to back of the X Idler of your RepRap Huxley (use longer m3 screw if necessary) [FOR REPRAPPRO...

Rafts: Doesn't MatterSupports: YesResolution: 0.2mmInfill: 15%Notes:I printed the parts in ABS and used Acetone to weld them together.There is a bracket which is designed to mount onto the chassis of the Huxley, and the boxes clip onto it - if your...

There is a bracket which is designed to mount onto the chassis of the Huxley, and the boxes clip onto it - if your wiring is modular, this means that you can remove/mount the electronics quickly when moving the printer. ...If the mount is to be used,...

Box for the Sanguinololu MCU board, with additional boxes for power input, power switch and lids. Print Settings Printer Brand: Printrbot Printer: Simple Black Rafts: Doesn't Matter Supports: Yes Resolution: 0.2mm Infill: 15% Notes: I printed the...

This is a thing to hold a microswitch to a 6mm rod. ... i use them for the Z and Y axes on my reprap huxley (original)

This is the version 2 cooling duct to be used with Reprap Huxley. The Huxley is very small and compact, this makes it quite hard to place cooling fans. This "Hose cooling" will take care of the cooling problem. You will need a strong fan/air pump. I...

Just an overdue upgrade for the reprap huxley. ...It allows me to plug in a small toggle switch alongside the power jack.

Instructions To compile the openscad files, you'll need to download parameters.scad and library.scad from the reprap huxley SVN. ...Print: 1x z top clamp.stl 1x z top clamp bar.stl Replace the existing Z top clamp with the new printed one Run your...

Replaces the rod holder on one of the huxley's Z axis uprights with a holder with built in mount for a wade's extruder. Designed for use with a bowden cable. Instructions To compile the openscad files, you'll need to download parameters.scad and...

I Noticed my Reprap Huxleys hot end fan was vibrating quite a lot, and i was getting wavy lines in my prints. I couldn't completely tighten my fan to the cooling block because some of the heat sink fins got caught in the fan, causing these...

A small foot that can clip onto the 6mm bars of a Mini-Mendel/Huxley RepRap printer. UPDATE 5.6.11: I should warn that I created these feet before constructing the Z axis, and it may be the case that these feet are too short with all the gears and...

I was having a problem with my Huxley PTFE hot end tube snagging on one of the support brackets for the controller board. I came up with this easy add-on deflector that solved my problem. You remove the mounting screw and slide the deflector over...

Our huxley was an intermediate model between major changes to the extruder drive and in our case the extruder drive holder proved too weak. It bend down and the big extruder gear collided with the frame. So I created a replacement which is twice as...

Buildvolume 150x150x200; laser cuttable on a 400x300mm laser cutter **Backstory: ** Basically this is the end result of me constantly updating my printer: 2011 - reprap huxley kit form eMaker 2012 - update stepper drivers and 2560 Atmega 2013 -...

Buildvolume 150x150x200; laser cuttable on a 400x300mm laser cutter Backstory: Basically this is the end result of me constantly updating my printer: 2011 - reprap huxley kit form eMaker 2012 - update stepper drivers and 2560 Atmega 2013 - updated...

A redesign of the printed parts of the RepRap Pro Huxley extruder, to use push-to-fit type connectors on each end of the Bowden tube. Made because we had lots of problems with the tube popping out under load from the extruder. The push-to-fit...

I was quite unsatisfied with the performance of the original axial part fan of the RepRap Huxley. After the good experience with the 50mm radial fans I used on my Rostock MAX, I decided to make them fit on the Huxley as well. ... Since I´am in the...

These are mudguard washers I printed for my Huxley. I couldn't find anything large enough with 3mm ID, so I made my own! ...Quick print, works great!

Instructions Print the 6 plates (2 to 3 hours per plate on a TOM) Buy a reprap huxley kit from http://reprappro.com/Huxley Build printer Print .... ...Printer Update 2012-05-09: Added z-endstop-holder.stl to the zip file it was missing :-( Added two...

I had a problem with the push fit type bearing holders in the stock Reprappro Huxley breaking every time (3 times) I tried to insert them. In truth the problem most likley lies in one of the following things 1) me being clumsy 2) not properly...

simple clip to light your printer's work Instructions you need 2 3x10 screws 2 M3 nuts 4 3 washers

Replace the initial part to add a switch.

Customized version of http://www.thingiverse.com/thing:71961 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=71961 Instructions Using the following options: ...

This is to hold a dial indicator on a RepRap 3D Printer to enable leveling the table.

It is difficult to adjust the distance between the large gear and the small gear because you need to undo the three screws which hold the stepper motor in place. By the same token it is difficult to remove the stepper motor without disassembling the...