reprap mendelmax 3d models

This is a snap on mount to attach a Galaxy Nexus to a mendelmax. I use this to run Octoprint on my old cracked phone. A phone is small, self contained unit with a decent camera and led. The camera and led can be exported to Octoprint and other...

i made a modified mount for the ulitbots fan duct (http://www.thingiverse.com/thing:28900) to mount them to a MendelMax (reaprap.cc kit)

I'm experimenting with the fantastic new MendelMax 2.0 from http://www.makerstoolworks.com/ I've taken the DXF's available here:http://github.com/Makers-Tool-Works/MendelMax-2.0/tree/master/Sources/dxf and Made (and modified) STL's with the intention...

Panel 1 - Keypad, LCD and Fan speed controller with one switch.Panel 2 - Keypad and LCD only.Panel 3 - Keypad, LCD and a blank space for switches etc.Panel 4 - Keypad, LCD and two switches.Please check dimensions etc before you print them, the knob...

Made a mash up of my original panel and the one made by Chillance. I made a few variants but I have only printed panel 1. Panel 1 - Keypad, LCD and Fan speed controller with one switch. Panel 2 - Keypad and LCD only. Panel 3 - Keypad, LCD and a blank...

... captured but my filament had a habit of unrolling. the only difference between the repraper arms and the regular arms is length. as you can see that is a repraper spool on the long arms in the pictures. ...I have sucessfully printed in ABS and PLA

MendelMax is a new RepRap 3d printer designed by Maxbots. It is a true reprap, using printed brackets, but instead of using threaded rod for the structural elements it uses inexpensive aluminum extrusions. This gives a huge increase in rigidity for a...

These are the printed parts for the RepRap MendelMax 1.5 3D Printer. Them used for the Frame. ... Manual for the MendelMax 1.5 3D Printer you get here: http://reprap.org/wiki/MendelMax

... of four of these parts. Once you've printed them, they should fit into place without having to disassemble any of the printer. You can find more about OhmEye's Z axis isolator here: http://www.ohmeye.com/2013/reprap-mendelmax-2-0-z-axis-isolation/.

... file included in case you want to improve on the design. When finished it mounts to the rear of the X-carriage as shown in the photo. Print Settings Printer Brand: RepRap Printer: MendelMax 3.0 Rafts: No Supports: Yes Resolution: 0.3 Infill: 40%

my first project, Panel Mendelmax Fan and Light switch Print Settings Printer Brand: RepRap Printer: Mendel Max Rafts: No Supports: No Resolution: 0,2mm Infill: 50%

Small toolbox for the MendelMax.

This is a simple foot for the excellent MendelMax RepRap ( http://www.thingiverse.com/thing:12645 ). I didn't like having the frame resting directly on a surface, especially when using black anodized aluminum. This helps prevent scratches. I...

Nothing Special just 8mm and 10mm end stops for my Mendelmax 1.5 build. ...I am sure these are derived from someone just not sure who.

Just a keychain to print on your MendelMax to show your friends what it can do. Instructions Print. ...Attach to keychain.

http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: stick_thickness = 5 Font = write/orbitron.dxf font_size = 14 font_thickness = 7 message = MendelMax stick_width = 11 flat_bottom = 1 hole_radius =...

... cable clip and some tubes attached to it. Print Settings Printer: Mendelmax 1.5 Rafts: No Supports: No Infill: doesn't matter; I have used 30% How I Designed This I imported the cable clip file into SCAD and added two tubes in an 25deg angle to it.

... there. Instructions When you slice this I suggest doing no fewer than four at a time. BTW - I did this part in PLA, if you are using ABS, you may have better luck with Wilson's MendelMax wire clip.

I wanted to jack up my new MendelMax so I can mount my power supply under there, but didn't like the look of any of the legs I could find on Thingiverse so I made these. They match the profile of the existing base pieces to keep things sexy and bolt...

I wanted to jack up my new MendelMax so I can mount my power supply under there, but didn't like the look of any of the legs I could find on Thingiverse so I made these. They match the profile of the existing base pieces to keep things sexy and bolt...

Print Settings Printer Brand: RepRap Printer: MendelMax 1.5 Rafts: No Supports: No Resolution: 0.3mm Infill: 20% Notes: Can be printed in ABS or PLA. The nut traps may be too shallow for your Z screw nuts. ... Barring an updated model here, a little...

COUPLER RepRap

REPRAP CHASSIS

A simple reprap logo keychain for the reprap lovers like me!

... this new machine is to save assembly time, especially for workshops. The latest sources, B.O.M, build manual and other information is on GitHub and the RepRap wiki. http://reprap.org/wiki/ITopiehttps://github.com/lautr3k/RepRap-iTopie Thank you.

The main purpose of this new machine is to increase rigidity and save assembly time, especially for workshops.The latest sources, B.O.M, build manual and other information is on GitHub and the RepRap...

Impresora 3D basada en el modelo Rostock del proyecto RepRap. ...El montaje fue realizado en el laboratorio de robótica de la Universidad de Pamplona - Colombia

I get the svg from reprap.org and made it into a 3d model useing blender and 123d design. I looked and did not see a logo for reprap and i thought that they needed one so here it is. ...Print Settings Printer: delta ...

The Reprap Wallace is now on github: https://github.com/whosawhatsis/RepRap-Wallace There is a video of an axis test using Marlin on youtube: http://www.youtube.com/watch?v=0QrEmGlZT0w&context=C3f40eeaADOEgsToPDskJ7qwV6fvNjtb93Wcpz_SHy More...

This is a Reprap pulley that will allow you to use 1/4" shaft motors without grinding down the shafts. ...I'm using this pulley with Keling Nema17 motors (model:KL17H247_168_4B)