retainer holder 3d models

retaining holder

Door holder remixed to fit my door spring. It is not that tight, but after printing I've heated a little bit the clip with a lighter and folded it just a little bit to get it tighter, and now it's perfect ! ...I've put a two-sided tape on the door side,...

This is a GM grill or molding retainer clip found on a lot of late model GM vehicles. This clip could possibly be used on other makes and models. Print Settings Printer: Malyan M150 ...

Designed to hold naked camera softmount for Betafpv pavo30, pavo25, Protek and etc

Slim shower curtain retainer holder tie back hook. ...Used for my shower curtain.

Long Hose Retainer and Holder Long Hose Retainer is used to retain the long hose when diving in a long hose configuration, without the need for a canister light to hold your hose in place. The hose retainer fits any standard 2" webbing and can be...

This is a positive-retaining holder for the LTT ratcheting Screwdriver. I've included the Solidworks source files for re-mixes as well as a belt-clip holder and a wall mount holder variant. Both should be printed upright and only the wall mount...

Holds two toothbrushes and retainer. ...Easy Clean if moisture builds up on bottom

This is a filament guide with a holder for the filament retainer made by https://www.thingiverse.com/thing:3627765 added a second version with filament runout sensor holder, it has a build in funnel to guide the filament right through the middle to...

... use one USB-C cable and attach Micro-USB or Lightning adapters to the end to make your own universal cable. The retainer helps you keep the adapters/dongles from getting lost. ... I attached pictures of the adapters I used (purchased from eBay).

LED Strip Holder that fit in the Machifit X Notch for LED Band of a maximum width if 8,5mm

Used to mount and hold these thrust bearings Needle or Ball (needle) 10mm Inner Diameter, 24mm OD, 4mm of Thickness (ball) 10mm x 24mm x 9mm https://www.amazon.com/dp/B07PDXP1S8?ref=ppx_yo2ov_dt_b_product_details&th=1 ...

This is a remix of the Case Retainer for the Lee Loadmaster. I found that the balls are just a bit too tall and had to grind them down to fit, so I re-worked them and made them smaller, but still functional. ... Remix_2

THIS IS NOT WORKING ATM As i am modifiing my Prusa i3 to have a more stable build carriage i made a customized version of http://www.thingiverse.com/thing:23882 I modified it with OpenSCAD (quick and dirty) to have a more robust and higher holder,...

Vertical Blinds Headrail Bracket. The headrail brackets on my vertical blinds were slowing breaking, so I made replacements. ... The step and f3d files are available as well, but be warned that this was a quick and dirty project.

Vertical Blinds Headrail Bracket. The headrail brackets on my vertical blinds were slowing breaking, so I made replacements. ... The step and f3d files are available as well, but be warned that this was a quick and dirty project.

Simple little cable holders I made for storing my DJI charging cables I printed these in clear PETG, and each take about 6 mins to print Enjoy, Alex

The batteries were always popping out from the battery holder. So I designed a simple battery retainer (clip) for the robots. It also fits common 6 x AA battery holder which are sized 90 mm x 58 mm x 16 mm. ... Link to the Fusion 360 model :...

Needed a "snap up" type of clip to hold on oil pan gasket for a jeep. I was impatient to order on so i churned one out real quick and dirty. ...The design is kinda crappy and quick but I thought I would Share for someone to improve on or use themselves.

Then I noticed Creality has changed their Retainer nut at some point. I looked around and could only find printable versions of the older 30mm hex nuts I already had. So I made this one. It's a tight fit for me, but the spool holder I printed was a...

... So I decided to just model it and print it. After a few attempts here's one that works well. It was inspired by https://www.thingiverse.com/thing:1457450 but I decided I wanted to keep the original wheel as only the holder was coming loose.

Description The original holder for the retaining band of the luggage compartment cover of my Toyota Aygo (2008) stopped working. It worked like a barb (you can see the original part in some of the pictures - used that one until I got an appropiate...

Shift Boot Collar Holder RetainerCompatibility :3/8 - 163/8 - 241/2 - 205/16 - 18 M8 x 1.25M10 x 1.25M10 x 1.5M12 x 1.25M12 x 1.5M12 x 1.75M16 x 1.5  example (civic 2007) : probably won't touch this file again so if you do...

I liked the design, but after a couple days of using it I had issues with some of the rounded bottom toothbrushes I have, so I made some small retainer rings that glue onto the bottom recesses

I designed this thing because the original holders broke. ...It's not a 100% copy, but they work great :)

.32mm shim that prevents your spool from rolling off the roller when slightly oversized. the design should self center the spool right? But if you pull it too fast, pull it wrong or your filament roll is slightly oversized it doesn't sit properly...

I'm pretty sure the actual size should be 15mm retaining clips, but I just bought the closest thing I could find at the hardware store and it worked well. Update: Make sure you get standard size retaining rings and not "heavy duty". ...The heavy duty...

Quick remix of the fantastic original, removing the battery retainer cutout, so you can slide the battery without using the retainer clip.

Quick remix of the fantastic original, removing the battery retainer cutout, so you can slide the battery without using the retainer clip. This version is not as ascetically appeasing as the original or my other remix...