retractable arm blade 3d models

Predator Scimitars (Arm Blades) the Scimitars (Arm Blades) from the series Predator All parts to be fused together with acetone The Predator Gauntlet is not included in the file the blades and other files can be found at Predator Gauntlet (Left arm)...

Push the slider button down and slide into three locking positions: to replace the blade, to use and to fully retract the blade for storage. To minimize slack, I designed the parts with close tolerances. Depending on printer and material, parts may...

Compact, discreet, with a retractable hook that Snap open or close. ...(Switch Blade inspired) Roughly 100 x 50 x 10mm size Cheers

Knives with retractable blade, assembled in 4 pieces without glue and without screws. Cutter Retractable Knife, four part assembly no need screw or glue . ... Video assembly here: https://youtu.be/cnAkYavJCNc...

Foldable arm used to provide vertical support.

Brazo con movimiento horizontal y vertical/Arm with horizontal and vertical movement.

I couldnt get the retractable blade to work on yeetkus's darksaber so I made my own that isn't retractable. It fits inside his, and is modeled accurately based on the darksaber. Sliced in multiple parts for smaller printers. I fused pieces with a...

... the cover on the body. If the blade doesn't slide or it's too hard to push just loosen the screws a little bit. Check out the new Remix Compatible with my ready to carry CarabinerBuckles System CarabinerBuckles - Retractable Xacto Blade Keychain

I really enjoyed 3DPRINTINGWORLD's collapsing lightsaber design, so I wanted to create my own lightsaber that worked with his retractable blades. I designed this lightsaber to be printed without any supports. This design includes a cap on the bottom...

... who knows, but people can always increase/decrease in their slicer as needed for their personal preferences. Last thing is I put a little extra width on the knob that holds the blade in when retracted to make it a little tighter against the blade.

... who knows, but people can always increase/decrease in their slicer as needed for their personal preferences. Last thing is I put a little extra width on the knob that holds the blade in when retracted to make it a little tighter against the blade.

This is a derivative of the the great design of https://www.thingiverse.com/thing:3606120 This is Yodas shorter light Saber with a shorter blade to match. ...

... the cover on the body. If the blade doesn't slide or it's too hard to push just loosen the screws a little bit or sand a the knob on the slider. Check out my other tools ready to carry with CarabinerBuckles CarabinerBuckles Utility Blade Knife

... are sunken. Blade width (at base); 3.5 cm Handle length: 10.5 cm To complete the assembly, a simple elastic bracelet of about 5 cm diameter and 2 axes of Ø2 x 15 mm are enough to complete this dagger in addition to the 4 pieces to be printed.

This is a remix of https://www.thingiverse.com/thing:3853024 which is a remix of https://www.thingiverse.com/thing:3677766 I adjusted the file for a smaller blade.

https://www.thingiverse.com/thing:69329 an arm with a blade added on, base model isn't my design but blade is.

This is my entry into the spare part contest. ...its the blade hoder for a Retractable Powagrip Trimming Knife.

This retractable razor blade scraper is an improvement over one I used to have for scraping burnt gunk off a ceramic stove top. Features: * No removable cap to get lost. Snaps into three positions: load/unload, safe storage, blade exposed. *...

Snaps into three positions: load/unload, safe storage, blade exposed.Sliding the top half all the way back exposes the blade for use.The middle position retracts the blade under the top half. In this position the hole on the handle end aligns in each...

... on the bottom for the removable blades. You can find those blade files here along with his instructions on how to print them: https://www.thingiverse.com/thing:3606120 For the best blade results, I printed each section of the blade in vase mode.

This is a derviative of this design https://www.thingiverse.com/thing:3606120 this is Quigon Jinns lightsaber with a slightly longer blade Assembly -Print all 6 pieces -take hilt_top and hilt_bottom and glue them together -glue button 1 into the slot...

Predator Scimitars (Arm Blades) the Scimitars (Arm Blades) from the series Predator All parts to be fused together with acetone The Predator Gauntlet is not included in the file the blades and other files can be found at Predator Gauntlet (Left arm)...

I come across them sometimes at the Pull-a-Part and they almost ALWAYS have a broken "arm" that locks the retractable light to the reel. I've found ones that were intact just to have the arm break off the first time I touch it :-/ The one in my...

Pantograph Type Blade arm

my version of the Predators arm Blades

Construction knife with retractable blade and breakable segments

my version of the Predators arm Blades Print Settings Printer: Flashforge creator pro Rafts: Yes Supports: Yes Resolution: .3 Infill: 10%

From an early teaser poster for the upcoming Netflix Transformers Siege series, we see Jetfire outfitted with a wicked arm blade! Well, can't have our Jetfires not having this on him. So by popular request, here's a 3d printable version of this...

... Slayers is up there next to Dragon Ball Z as one of my favorite anime of all time. The fact that it is far less known pains me as it's a fantastic series. So I had to print this but it wouldn't be complete without a retractable blade.

I was tired of taking my blade off after every time I used my utility knife. ...This was my solution.