reusable floss pick 3d models
28553 3d models found related to reusable floss pick.thingiverse
Like those floss picks you see littered everywhere on the street, except you can use it again and again.
prusaprinters
... importance. ...This 3D printed dental floss pick allows you to string any dental floss especially those trial size ones from the dentist and have a dental floss pick without having to go to the grocery store to restock and risking yourself to COVID-19.
thingiverse
A thing that holds and tightens floss from a roll so you can floss your teeth without shoving your fingers into your mouth. ...Uses an 8-32 x 1-1/2" machine screw, though you could use other sizes if you tried hard enough.
thingiverse
This is a Floss Pick holder that can be put on your keychain, it carries three floss picks for easy flossing anytime you need. The only floss picks that will fit are the DenTek brand just like the ones in the picture. ...they should be fairly easy to...
thingiverse
The main purpose of it is that the pick will remain the same but the floss will be changed every time. This changing of floss will make the issue of bacteria spreading from old floss not an issue. ...It is a product that can help save plastic over time...
thingiverse
Dispenser for floss picks. This is currently a work in progress. Spring used is 6.8mm (inner diameter) x 50mm (length). I estimated the minimum compression to be about 20mm, so that is what I made the height of the carrier. This might be...
thingiverse
I wanted something to hold my floss picks after opening a new bag of them, as I find it annoying to have to dig around in a big bag of them each time I need one, and also wanted something I could use for travel and the like. It can be placed on its...
thingiverse
-Not wanting to have an ugly bag in your cabinet where all the floss picks get unorganized + and contaminated each time you reach your hands in? Look no further. Remixed version so you can hang it in a cabinet and have enough picks to last 2-3...
prusaprinters
... I need them. ... There's a small channel at the base to prevent it from holding water because the last thing anyone wants to do is shove a piece of a mouldy pick into their mouth. Printed in white eSun PLA+ at 0.2mm and no supports.
thingiverse
A simple mount for the quip refillable floss pick. Can probably work without the magnets, but feels like a much better experience with them included. ... Uses these...
thingiverse
Fancy clip things make it easy to hold the floss, and 2 strands for twice the flossing power. ... Print with the angled parts of the barbed clips facing down.
prusaprinters
These floss picks are easy to use and they are both a tooth pick and floss, so I really like them and they have upped my flossing game.Carrying them around however can be a problem if they get bent, or worse dirty since you're going to be sticking...
thingiverse
Replacement pod for the quip refillable floss pick. No supports needed. I found the easiest way to refill it was wrapping the floss around half a toothpick while keeping the first couple inches free. Take that first bit and feed it through the pod...
thingiverse
Customized version of http://www.thingiverse.com/thing:59332 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=59332
thingiverse
Customized version of http://www.thingiverse.com/thing:59332 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=59332
thingiverse
Customized version of http://www.thingiverse.com/thing:1201466 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1201466
thingiverse
Customized version of http://www.thingiverse.com/thing:59332 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=59332
thingiverse
Customized version of http://www.thingiverse.com/thing:59332 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=59332
thingiverse
Customized version of http://www.thingiverse.com/thing:59332 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=59332
thingiverse
- Simple stand to keep everyone's dental accessories organized - Printed in PLA, 4 walls, 8% gyroid infill - Print standard version - with hole trough - rear side touching build plate - no supports - Leak free version - no hole trough - bottom...
thingiverse
Needed a place to put toothbrush in the shower, so I designed something!
grabcad
For the original design you have to buy more floss online and wait for it to ship, but with our redesigning, the difference is our handle will fit the floss container itself on it so it is truly reusable design you can simply go to the store and buy...