revolute joints 3d models

Customized version of http://www.thingiverse.com/thing:339039 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=339039 Instructions Using the following options:...

Customized version of http://www.thingiverse.com/thing:339039 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=339039 Using the following settings: MagnetHeight is set to 3 JointRestAngle is fixed...

Articulation parts for action figures (Mcfarlane, Mafex, Etc.) It all depends on the design and type of articulation of the figure. Attention, the pieces being small can be complicated to print and that they fit perfectly, it is recommended to print...

Built as support for rolling jonnies. ;-) Printed a materialsaving version with no infill to save materials on prints. The wall thickness of the design is 0.8mm, so it prints perfectly with two perimeters each at 0.4mm line width. Added a small...

This week, I'll be attending the Royl Cornwall Show in the UK and showcasing Robotic Football using teaching robots. Since all goals were occupied, I decided to create my own visually appealing goal set. The goal parts require an overflow pipe (OD...

Customized version of http://www.thingiverse.com/thing:339039 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=339039 Instructions Using the following options:...

Customized version of https://www.thingiverse.com/thing:339039 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=339039

This tiny device is a helping device to build 6 arms of the exact same length. You'll need two of them. Instructions Print two of these, put M3 nuts is the suitable holes (you'll need to warm them...

Customized version of https://www.thingiverse.com/thing:339039 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=339039

I present to you my revised doll high chair, an upgraded version of its predecessor which was unfortunately too fragile. To address this issue, I created an enhanced model. As I worked on assembling the puzzle plane, an innovative solution emerged -...

I crafted this Death Star model into a massive wall hanger, roughly one and a half feet in diameter or 40 cm. The front half was carefully cut into 16 pieces designed to seamlessly fit together on a Robo 3D R1 Plus. To ensure precise alignment during...

I crafted an Air Plant Hanger using sturdy 1/2 inch (13mm) wood dowels. To replicate the one shown, simply use the top-selling STL file and print with supports in place for added security. I deliberately left the supports intact to amplify the...

I needed to make several Pokeballs for an event but when I printed them they were too rough because of the supports, so I designed a simple pokeball, cut it in 2 parts (so that the union is not appreciated) and added some holes with some sticks to...

Customized version of http://www.thingiverse.com/thing:1251169 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1251169 Instructions Using the following options: customLidFinger = 20 customZ = 40...

Reimagined from the original blueprint by chemteacher628 (https://www.thingiverse.com/thing:1261572), this DNA/RNA building set gets a high-tech makeover with enhanced design features that make it easier to assemble and print in 3D. Students can now...

Customized version of http://www.thingiverse.com/thing:1251169 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1251169 Instructions Using the following settings: Layout2D customized = Off Finger...

Instructions to assemble and print a customized keychain: To start printing your custom keychain, first ensure you have downloaded and installed the required slicing software. Select the following options in the customization menu: Set finger...

Customized version of http://www.thingiverse.com/thing:339039 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=339039 Instructions Using the following settings: JointRestAngle is set to 30 degrees. JointDistance is...

Customized version of https://www.thingiverse.com/thing:1251169 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1251169

Customized version of https://www.thingiverse.com/thing:339039 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=339039

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/3nvfno3RjWb