rgt ex86100 3d models
97 3d models found related to rgt ex86100.thingiverse
Here is my full roof rack for a RGT EX86100. The rack is made so you can fix it with 10mm diameter magnets. I have made two versions of this. The light version weights about 60gr. while the stronger version weights about 100gr. ... I left some space...
cults3d
RGT EX86100 body support EX86100 Printing horizontally using brackets will improve rollover resistance.
thingiverse
Custom back lights. ... Requires: - 4 red 5mm LEDs - transparent plastic and red tape as glass - silver paint to increase reflection of internal space - thermo glue for fixing
thingiverse
These parts are for a RGT ex86100 RC crawler. I ordered a front and rear bumper for a TRX4, but the holes in the RGT don't match. Those parts replace the bumper mounts on the RGT. ... You can use the screws from the car, 4 x M3 If you want the fusion...
thingiverse
I think the original body posts (front and rear) of the RGT EX86100 1/10 crawler are very weak. The body slides a lot and I found it difficult to put the body on both left and right posts at the same time on my crawler. So, I decided do design and...
thingiverse
This is my own design for a spare wheel which looks just like the original 6 hexagons of the RGT EX861000 1/10 crawler. ...
thingiverse
This is my own design for OEM side steps for the RGT EX861000 1/10 crawler. You have 4 files: left and right side step and left and right mount to the chassis. I just replaced the short chassis screws with the long bumper screws so I could scrw...
thingiverse
I wanted to make my own winch for my RGT EX861000 so I designed and printed it. You just need to buy a N20 motor with gears. I got a 12V 200rpm for less than 3€ and print these 3 files. The winch will fit the bumper bars so no need for screws. You...
thingiverse
This is the mount for aditional led's or replacement of original led mounts of the RGT EX861 crawler-
thingiverse
Площадка для крепления серволебёдки на RGT EX86190 Для установки нужно снять пластик имитации двигателя, штатную переднюю площадку. ...
thingiverse
RGT CHub 14 Degree Mirror it in your slicer to print the opposite
thingiverse
i decided to make this to make the RGT axle have a maximum performance and nice steering geometry, RGT EX-86120 or any RGT-RC need work with the steering link or use another steer link need 95mm servo link M3 tap drill the Chub (knuckle mount)
cgtrader
It is RGT 3d engine, Designed by Markos in 3d's max 2008 and rendered by V-Ray in 3d's max 2016. ... Regards,
thingiverse
Il comprend : -Support carrosserie avant -Ecrou carré pour visser les aimants dans les supports de carrosserie d'origine -Support carrosserie arrière -Traverse de liaison cabine-benne -Réhausseur de pare-choc arrière (4 versions) -Rallonge de...
thingiverse
This front grill is specially designed for RGT Rock Cruiser with Defender body. Printed with 0.4mm nozzle, 0.1 layer height. ... Strictly for personal and private use, not licenced for commercial use or reproduction or in connection with any...
thingiverse
This side guards is specially designed for RGT Rock Cruiser. Compatible with ECX Barrage or FTX Outback. Printed with 0.4mm nozzle, 0.2 layer height. ... Additionaly needed: - 4x M3x10 screw - 4x M3 nut - 8x M3 washer Strictly for personal...
thingiverse
This spare tire carrier is specially designed for RGT Rock Cruiser. Compatible with ECX Barrage or FTX Outback. There are three version. Flat, angled with 4.8 and 6.5 degrees, because the bumper is not perpendicular to body. For my way is best 4.7...
thingiverse
This is anti-rotation links for RGT 136100 V3 for snowtracks by Mh2241 https://www.thingiverse.com/thing:5222976 Front one is same for left and right side. Rear one here is model for right side. For rear left side just use mirror in slicer. For...
thingiverse
Wahoo RGT CherryMX handlebar button mounts for USB connected A & D buttons for steering. **Mirror the STL file for other handlebar orientation** Printed in TPU for to create a snug fit with some flexibility. These fit my Shimano shifters...
thingiverse
My own design for a jerrycan mount for the rear of the RGT EX86100 which also has a large tyre. This solution allows to fit the jerrycan in one side of the spare tyre. ... Made for this jerrycan: https://www.thingiverse.com/thing:2571350
cults3d
body mount set to join hsp rgt chassis to loops rc lc90/ bundera cab and body
cults3d
rgt 1:10 rear chassis crossmember with tow hitch receiver may also fit others
thingiverse
It is designed for RGT Rock Cruiser (1:12) and RGT EX86100 (1:10). Compatible with ECX Barrage or FTX Outback. Printed with 0.4mm nozzle, 0.2 layer height and supports is ON. Strictly for personal and private use, not licenced for commercial...
thingiverse
Customized version of https://www.thingiverse.com/thing:2403440 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2403440
thingiverse
Panhard mount for elemination of bump steer, need to remove 4th link from axle for correct work of panhard and servo on chassis.