richrap 3dr

This is a redesigned carriage for a richrap 3DR printer (or derivative). It is to be used with a 6mm gt2 belt and 8mm steel rods with 8x12x20 oilite bronze bushings. The freecad files are included to allow easy modification to other bearing types and...

E3D V5/V6 Holder for Richrap 3DR Instructions Uses 2 pcs M3 screws and nuts to clamp. ...Uses 4 pcs M3 connect to effector.

... on the Smooth Rods themselves. ...There is a screw that will press against the 20x20 extrusion to lift the whole Pulley part to tighten the belt. Print Settings Printer Brand: RepRap Printer: Richrap 3DR Rafts: Doesn't Matter Supports: Doesn't Matter

See RichRap's wonderfully detailed guide here: http://richrap.blogspot.co.uk/2013/07/3dr-reprap-delta-printer-part-1-release.htmlSource filesRichRap's 3DR - Modified for 8mm Rod and 20mm Box section (Squared Wood, Extruded Aluminium or Box Section...

Customized version of http://www.thingiverse.com/thing:285405 for "RepRap obchod" HotEnd and My remix 3DR RichRap & 3DR Simple printer... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=285405 ...

Customized version of http://www.thingiverse.com/thing:285405 for the Hexagon 1.75 Hot End by Reprapdiscount.com Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=285405 ...

This is an alternate way to mount a RAMPS 1.4/Arduino Mega 2650 board to the RichRap 3DR using the 8mm threaded rod and M8 nuts for the spool holder instead of the 3mm stand-offs in the electronics mount which were weak and didn't fit the M3 bolts I...

This is an alternate way to mount a RAMPS 1.4/Arduino Mega 2650 board to the RichRap 3DR using the 8mm threaded rod and M8 nuts for the spool holder instead of the 3mm stand-offs in the electronics mount which were weak and didn't fit the M3 bolts I...

Carrying handle for RichRap's 3DR delta printer

... at all... Instructions These are extensions to RichRaps Mavellous 3DR Delta RepRap, They sit between each top and bottom 'corner' to extend the overall printable area. ...Make sure you accommodate for extra wire and rod length where necessary...

Customized version of http://www.thingiverse.com/thing:285405 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=285405

Customized version of http://www.thingiverse.com/thing:285405 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=285405 Instructions Using the following options: PHI =...

Customized version of http://www.thingiverse.com/thing:285405 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=285405 Instructions Using the following options:...

Customized version of http://www.thingiverse.com/thing:285405 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=285405 Instructions Using the following options:...

Richrap's original hotend mount and micro platform combo works fine, but I couldn't attach the fan which is shipped with E3D hotend because there was not enough space. So I reworked it. 6 mounting holes are 2cm away from each other. ... It will...

My version of hot-end mount for RichRap's 3DR delta

Carriages for RichRap's 3DR, modified by JEZZMUND for 8mm Rod (using LM8UU bearings) and then my by myself to fit GT2 belt instead of spectra fishing line. ... I haven't assembled my 3DR yet, however, I've printed the carriages to confirm that GT2 belt...

This is a ground-up remodelling of the Micro platform / actuator carriage for RichRaps 3DR Delta Printer. This has the corner screw mount points and should have adequate clearance for all 4 of the E3D Hotends to be mounted simultaneously while...

My version of YRUDS bowden extruder for RichRap's 3DR delta BOM: Mount: 2x M4 10mm screew 2x M4 hammer nut 2x M4 washer (optional, I did not use them) Idler: 1x 626 bearing (19x6x6mm) 1x M6 25mm screew 2x M6 washer 1x M6 nut Spring mount: spring ID...

all the files for the RichRap 3DR Delta printer and derivatives are covered by - Attribution - ShareAlike Creative Commons V3 (CC BY-SA3.0) Much Gratitude to RichRap for his excellent work on this design. All credit and 'props' where it's due,...

Panelsan is LCD case from U-Design's BiB One 3d Printer:http://www.thingiverse.com/thing:21178 file inside RAR archive: "1x panelsan obudowa.stl" Additionally I designed my own knob for encoder.

This Thingi is a Idler for the Richrap and also the JohnSL 3DR. It Idles the Fishingline like Prusa X Belt Idler. M4 Nut in the Top Nuttrap. An M4 Screws through the Bearings with 2 Washers. It tightend with a Nut for the Aluextrusion. The...

Handle for the RichRap 3DR. ...Should screw onto the extrusions using M5 screws and t-nuts.

This is a adaptator for 70mm fan for richrap's 3dr .

This is a modified richrap's 3dr joint. ...It work perfectly with traxxas 1942 and 3mm carbon stem.

This is a modified richrap's 3dr joint. ...It work perfectly with traxxas 1942 and 3mm carbon stem.

Three small adapters that allows a standard RAMPS+Mega Electronics kit to fit onto a RichRap 3DR printer: http://richrap.blogspot.co.uk/2013/07/3dr-reprap-delta-printer-part-1-release.html ...

Big Heatbed needed (mine is a Homemade TAZ) Based on the JohnSL modiffications of the RichRap´s 3DR Delta Printerhttps://github.com/JohnSL/3DR-Simple-Delta-Printerhttp://richrap.github.io/3DR-Delta-Printer/

This adapter allows the use of spools with internal diameter of 52mm on the RichRap 3DR.The tall piece should slip directly over the original spool holder with bearing.The spacer piece lifts the whole spool above the idler bearing covers if the spool...

... using it. BOM: printed platform part (of course) 1 x 10cm M8 threaded rod 1 x 608ZZ bearing 2 x M8 bolts (1 inside RIchRap 3DR top boss) 4 x M8 washers (optionaly you can use the printed one) Instructions Follow the pictures in order to assemble it