rifle scope camera side mount 3d models
677067 3d models found related to rifle scope camera side mount.
thingiverse
Allows for the usage of the camera on both sides of the mount. Requires 4x fi 3 and 4x fi 2 mm screws with nuts for mounting. Theoretically, it allows for the usage of 3.5 mm and 2.0 mm screws. ...However, I'm not too fond of the tolerances of the holes...
thingiverse
This mounting system attaches a keychain spy camera to an Ultra Stick Mini plane, using a likely 4-40 size bolt and nut at its pivot point. The side walls may need Dremeling for camera fitment; it was acquired via eBay. ...A rubber band secures the lid...
thingiverse
This mount fits into the top accessory mount of the camera and can serve as a GoPro mount or attach to GoPro mounts. It works seamlessly with the GoPro Knuckles Handle by "suatbatu". (https://www.thingiverse.com/thing:487964) Originally, I designed...
thingiverse
... replace top button with button_replacement for anchor point. Mount cameras by removing tilt bracket and using saved screws to attach camera_base; attach camera to base with M3 screws and install final screws, springs, and nuts as shown in pictures.
thingiverse
Micro camera mount for the craftedkwads Pegasus variable stance frame. NOTE: THIS IS NOT SYMMETRICAL. You can print them the same way but make sure when you put them on the inner sides match up with a 19mm camera. Its pretty obvious which side does...
thingiverse
This is a part of a **camera mount** that can be attached to a compatible frame using screws. The file only includes the right side. To obtain the other side, you must mirror the part in your slicer. ... - Compatible with some digital camera feed...
thingiverse
... the supplied file and use double-sided adhesive tape for easy positioning during installation. Alter the top mount on both sides and secure it in place using adhesive tape as well. ...Trim any excess plastic to prevent obstruction of the camera.
prusaprinters
SummaryCreated an adapter that will add a rail mount on a Meade 2114 (114mm) reflector telescope for mounting a red dot or other spotting scope. This replaces the ring adapter for a straight through spotting scope. Its based off the rail mount for...
thingiverse
Hey, this is an easy-to-use Camera Mount designed specifically for the Anycubic i3 Mega. Simply place it at the top and secure it with one longer screw or attach it to the side using a screw from the frame. This sturdy mount can confidently hold your...
cults3d
... onto the right side and should work with most webcams. I use the Logitech HD Pro Webcam C920. You will need one 3/4 inch long 1/4-20 screw. Here is a video from the mounted camera: http://www.youtube.com/watch?v=zQcbwoxPA0g&feature=youtu.be
prusaprinters
... for the MakerGear M2. ...It snaps onto the right side and should work with most webcams. I use the Logitech HD Pro Webcam C920. You will need one 3/4 inch long 1/4-20 screw. Here is a video from the mounted camera: Category: 3D Printer Accessories
thingiverse
Rifle standoff designed to compensate for shorter scope length now reaches standard resting positions securely. ...Six by three millimeter magnet recesses are expertly positioned for optimal magnetic attachment.
thingiverse
1) Mount your scope in the dummy rings. 2) Measure the distance between scope bottom and barrel top. 3) Subtract that distance from 15mm. --> The result is your minimum needed build height. Remember to add some if you intend to use external...
thingiverse
... with an additional M5 nut. I designed it for the internals of an old webcam that I had, but it should also fit a Raspberry Pi camera module. You can either stick the camera to it using double sided tape or drill some small holes and use some screws.
thingiverse
... with support. Glue the smooth side of the Hat Clip Base to the bottom of the camera clip. Then glue the short end of the hat clip to the bottom of the camera clip in the notch. ...Be sure the hat clip fits into the notch in the base before gluing!
thingiverse
... the weight keeps it locked in place. ...Lift slightly to slide it side to side. It has 3 holes for mounting a camera via the .25 / 20 tripod mount, and even comes with a printable bolt I use it with a logitech clone as you can see in the images.
thingiverse
Tripod collar for Ernitec TV-zoom lens (12.5mm-75mm F1.8) to use as a telescope guide scope. Design has 34mm vixen style wedge mount to connect telescope. ... M4 bolt & nut is needed to tighten the collar.
cults3d
Reptillia rmr mount coming soon If you want me to remake the rings for a different diameter of scope, leave a comment and I will see if I can make one I am not responsible if it breaks and you lose a scope, print however you need to in order to make...