rigid heddle loom 3d models

This is a mini rigid heddle loom, inspired by the open source looms made by the interlace project. It's still very much a work in progress, but I wanted to make it available to anyone who wants to experiment with it. ... Everything I've done so far has...

This is not the most efficient way to make a rigid heddle loom, but it works. There are definitely some parts that need some editing, the heddle needs to be stronger, as do the front and back round beams. Also, the openSCAD files should be...

Resources on setting up and using rigid heddle looms can be found here: https://www.ashford.co.nz/tutorials/weaving-tutorials Assembling the heddle requires friction welding. The technique is described here:...

Resources on setting up and using rigid heddle looms can be found here: https://www.ashford.co.nz/tutorials/weaving-tutorials Assembling the heddle requires friction welding. The technique is described here:...

> See original post for 8-, 10-, and 12-dent screens: https://www.thingiverse.com/thing:490467 > Print a reed threading hook from here: https://www.thingiverse.com/thing:3405655 > Printed my own shuttle: https://www.thingiverse.com/thing:5759232...

https://www.youtube.com/watch?v=fa1WrHOTjxY To simplify the weaving and warping process I changed the standard rigid heddle loom design. Tie your warp strings to one of the dowel rods instead of the warping stick like shown in the video. There will...

This is a bobbin I made for a friends large rigid heddle loom. It fits in a bobbin winder and the shuttle she uses. ... Print upright with supports.

...... This was developed from The Interlace Project's original laser-cut Rigid Heddle loom, with a few small changes. It was increased in width to accommodate a 16" weaving area, and lengthened by three inches to all for the double heddle to move easier.

Its a remix of a rigid heddle loom to reduce the printing time. The woodframe needs 30x20 mm wood. I improved the Heddle to make it sturdier. For the beam I used 30mm round wood and cut a 20x20mm square on each side to fit on the crossbeam...

This is a simple Ridgid Heddle loom, where the reed can split open to allow for easy warping/stringing. The simple design is my own, I have never seen a "split reed loom" before, but I doubt that I am the first one to come up with this, as the idea...

A fully working loom, no need for any other materials ready to use from the printer, no need for metal screw( you can use them if you want) You just need to print and assemble the parts, there a lots of tutorial videos of how to use it I recommend...

This is a small, highly portable rigid heddle backstrap loom. Your first project can be a new backstrap, and you can use paracord, USB cable, shoelaces, or whatever you want to stand in until you have your newly woven strap. You'll need a...

I was heavily influenced by the designs of: ProgressTH: https://www.thingiverse.com/thing:2449174 skottyorr: https://www.thingiverse.com/thing:1065906 and eried: https://www.thingiverse.com/thing:15120 but I didn't use anything from their...

Added one more file for a stand up loom with a larger outer diameter gear (roughly 85.4mm outer diameter gear). Some slight scaling may be needed if your printing settings are different. Test printed on a MakerGear M2 using Simplify3D. ... ...

double heddle block for ten16's rigid heddle loom print 2 of these instead of the heddle braces from ten16 and print a second heddle because of the holes you might need supports I didn't need them because of the modifications we made to the printer

[German Version below] I have adapted the creel combs for the Loom Erika made from Allgaeu and they also fit the Buttinette loom. The gate combs are each 10cm wide, so you can print it out on a small 3D printer and piece it together. You only have to...

Remixed from Ten16's Rigid heddle loom and the Nora1410xd's double heddle remix. Added holes for support bars to run the width of the loom for a wider (24in+) warp as anything wider than 16in tends to torque with the tension. The support bars should...

4th heddle block for Ashford rigid heddle loom. This is if you want to weave 4 shaft pattern with 4 heddles with Ashford Knitter's loom. Use 3M strips to attach to the sides. ... Link for the 3 rigid heddle holder,...

A modified version of double rigid heddle holder for Ashford Knitter's loom into three rigid heddle holder. I updated the stl file to V8. This version would anchor to the loom much better than using 3d pegs. Get 2 of 3/16inch diameter and 3/4inch...

Thanks to rjrahardjo for the three rigid heddle holder! As I just need a double one on my Ashford Knitter's Loom and the original wooden one is about 40€, I just cut the three one. ...Therefor right and left is the same one.

Rigid heddle for rigid heddle loom 9 -10 dpi. ... Four of these will be about 13 inches of weaving width.

The included print files are 200mm (~8 inches) sections of reed for a rigid heddle to be used on a rigid heddle loom. It is intended to be mounted in a suitable frame with a 1/8" wide slot routed 3/8" deep. It is designed so that multiple sections...

Remixed from/for Ten16's Rigid heddle loom. My mom wanted to use the Ashford Knitters Loom Ratchet and pawl set instead of the printed ratchet and pawl for added strength and consistency, so we lengthened the corners and put the pawl hole all the way...

small rigid heddle

... to get a STL file and 2D to get a DFX for laser cutting. For anyone who wonders: "A heddle is an integral part of a loom. Each thread in the warp passes through a heddle, which is used to separate the warp threads for the passage of the weft. ..."

This can allow you to convert your Cricket rigid-heddle loom into a multi-shaft loom. The maximum that works well in my experience is four shafts. ... You'll need to print two, some dowels, and some flexible heddles (just strings tied in a loop, works...

... version of http://www.thingiverse.com/thing:1223978 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1223978 Instructions Using the following options: warp_count = 20 warp_diameter = .5 heddle_height = 10 2Dv3D = 3D

This is a Heddle frame compatible with the reeds and heddle clamp found here https://www.thingiverse.com/thing:1065906 This would be used instead of the wooden frames to hold the reeds together, making this project fully 3D printable. ...This file is 15...

This is a 4 inch X 4 inch X 1/8th inch (101X101X3mm) Rigid Heddle insert. It is designed to be stack-able end to end to obtain the desired width. If your heddle is not a multiple of 4 inch units then you can easily cut the final one to the desired...

Based on their single heddle block I've created this double heddle block (as a remix) for use on their ten16-RHL (rigid heddle loom.) Printed on Draft (0.3mm), 25% infill, no supports. ... <hr> <b>Update: RHL_NewDoubleHeddleBlock.stl</b> This new...