rigol dp832 3d models
88 3d models found related to rigol dp832.thingiverse
;-) In my Rigol DP832 is a SUNON ME80251V1-000C-A99 fan installed: RATED SPEED: 3200 RPM AIR FLOW: 69.65 m³/h STATIC PRESSURE: 4.57 mm H₂O ACOUSTIC NOISE: 33 dB(A) CURRENT @ 12V (measured): 136mA I could not find a 80mm fan which had a similar air...
thingiverse
Riser feet to tilt display upward for easier viewing when power supply is on desktop rather than an eye-level shelf. Wide base for stability. Sketchup design file included. ... Edited Mar-3-2020: Added shorter version.
thingiverse
Simple replacement knob for the Rigol DS1052E. ... My small buttons on my Rigol Oscilloscope cracked and the only replacements I've found to print don't fit.
thingiverse
mount your Rigol Oszi to a Wall. ...Attention, a 90° power plug is needed.
thingiverse
This is a lock for Rigols Probe. ...By attaching it to the probe, the probe's multiplier is locked to x10.
thingiverse
Rigol DS1054Z Probe Holder. There is not much more to say about this. ... Fusion 360 for customization and export: http://a360.co/2CJeel3
prusaprinters
Replacement knob for broken one on Rigol oscilloscope. ...6mm shaft.</p><p>Printed in white filament PM. </p><p><i>Print instructions: Layer height 0,1mm, no supports. </i></p>
thingiverse
Siple Probe Holder for Rigol Probes (eg the infamous DSO 1054z) These do NOT clip in tight. However, they will not fall down if you brush the cables below. ... Very low insertion pressure is necessary to ensure probe longevity.
thingiverse
This is a replacement for the plastic ring that snaps onto the probes included with the Rigol DS1054Z oscilloscope. ...You can print as many as you'd like, and in any color!
cgtrader
Highpoly model of Rigol Oscilloscope for laboratory measurements. Modeled in Blender 2.9 and rendered by Cycles. Backside is not modeled ! Materials are PBR an textures made in Substance Painter in 4K. Decals Alpha included. All parts are unwraped.
thingiverse
This holder is designed in a way that a Rigol DS1054Z fits seamlessly on the holder. However, it is no tight fit so if you lift the scope, this won't stick to it. Feel free to improve this, I've also uploaded the Fusion360 project. The uploaded...
thingiverse
I designed a stand for my Rigol DS1102 that would let my bench power supply sit underneath it. Perhaps someone else might find this useful. You'll need to print two copies of this STL file, one for each end of the scope. ...There is no crossbrace,...
prusaprinters
mount your Rigol Oszi to a Wall. ...Attention, a 90° power plug is needed.</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p><p class="detail-setting printer"><strong>Printer: </strong>...
thingiverse
Rigol DS1054Z scope wall mount Remix of Rigol DS1xx4Z scope wall mount bracket" by Masterkookus - thinner - less material - reduced print time
thingiverse
Parts-Holder for Rigol Probe Print Settings Printer Brand: Up! ... Printer: Up Plus2 ...
thingiverse
This probe tray is designed to store the probes of the Rigol 1054Z, Just because I didn't like the bags provided. ...The trays are stackable and comes with a lit for the one on the top.
thingiverse
It's an adapter you clip behind a Rigol DS1054Z Oscilloscope and put 3 Worx 20V battery to power it. No circuit required, batteries are in series on the AC input. ... Last +/-4 Hours on 1.5Ah Batteries
grabcad
... thread, just a 2.5mm diameter hole. You can either tap the hole or just thread a M3x0.5 male thread into the clamp after it is printed. The outside diameter of the Rigol probe is approximately 11mm and the internal diameter of the clamp is 10.5mm.
prusaprinters
This probe tray is designed to store the probes of the Rigol 1054Z, Just because I didn't like the bags provided. The trays are stackable and comes with a lit for the one on the top. Category: Tool Holders & Boxes
thingiverse
The trigger button on my Rigol DS1052E oscilloscope broke (it cracked). So I needed a replacement one. ... Changes to blackboots' model: - made the number of ridges around the knob adjustable - the flat side on the shaft doesn't go all the way down...
thingiverse
Every time I'd press the power button or try to insert a USB stick into my Rigol 1054z Oscilloscope, the scope would slide back on the shelf, causing a half-inserted stick. This foot hold keeps my 1054z from sliding backwards. I can now power it...
thingiverse
I got a new Rigol ds1054z scope that came with Rigol PVP2150 probes (the smaller, all black kind), and I needed something to hold the probes in place on circuit boards. I had already printed this very nice probing station designed by giufini: ...
thingiverse
Mounting Bracket for Rigol 1054Z series Oscilloscope (should work for 1xx4Z series as I think they all share the same body).
thingiverse
These are probe holders for Rigol RM-DS1000Z rack kit. 4x M4x12 or M4x14 countersunk screws are needed for mounting. ... Designed for RP2200 probes.
thingiverse
This is a vesa mount for a Rigol DS1054 oscilloscope, I needed to mount mine underneath my keyboard tray. ... I've also designed a drop-down 90 degree vesa adapter that I use together with it.
thingiverse
Heavily inspired by https://www.thingiverse.com/thing:4935122 Oscilloscope Probe to Wire Adapter by DamianB2 Their design fits Siglent probes but not my Rigol probes. The spring terminal are Molex 0008500113 Cut the carrier strip between the...
prusaprinters
Oscilloscope probe to wire adapterFor Rigol probes (PVP2150, DS1054Z)This allows for a soldered probe connection with minimized lead inductance. Heavily inspired by https://www.thingiverse.com/thing:4935122Oscilloscope Probe to Wire Adapter by...
grabcad
Outside diameter of the lower portion of Rigol probe is ~6.5mm where the clamp fits. ... Internal hole in part is is 2.5mm, intended to be tapped to accept a M3x0.5 male thread or you could just screw the M3x0.5 thread into the plastic if you 3D print...
thingiverse
Table stand for the RIGOL DS1054Z oscilloscope with probe holders. The stand will raise the oscilloscope by 130mm to make more room on your crowded work table, and the screens won't be blocked by multi-meter or the soldering station anymore. There...