riser for tv 3d models
2238578 3d models found related to riser for tv.thingiverse
This thing was created first out of necessity for a Bose soundbar to fit under a Vizio TV, then a year later I needed it taller for a similar TV to allow it to fit in the cabinent where the doors were wide enough but the hinges stuck out. I saw the...
thingiverse
Placing a soundbar in front of the TV I had problems with the IR receiver of the remote and always had to raise my arm, so I decided to create these 2cm rises. They are specific for Sony XF9005/X900F series TVs. They have an "I" sign indicating...
thingiverse
Front and rear blocks used to raise Sony TV over soundbar. ...Specifically formed around front of Sonos Arc soundbar and fits the angle of Sony's TV mount. ...Print two of each and mount your TV over your Sonos Arc.
thingiverse
Riser for 2019 model LG 43UM7300PUA TV. Wanted something to lift it up higher than my Energy Center-channel speaker so that it won't block the screen nor the IR receiver. ...
thingiverse
... to put something (eg. ...BR-/DVD-Player) underneath your Nokia Smart TV 5800A or 6500A you can use this model to raise the Smart TV. It lifts the TV 43mm (1.7") higher. ... I printed it in PLA and sprayed it with black paint to match the TV better.
cults3d
Si vous n'avez pas d'imprimante 3D et que le produit vous intéresse, rdv sur Etsy ou vous pourrez passer commande :...
thingiverse
I created a tunnel and a notch for cable management and to reduce some PLA The stl file was designed for right support with notch inside but you can apply a mirror effect on your slicer to get the left one and you can modify all the dimensions to...
thingiverse
So I wanted to place my soundbar directly under my standing flatscreen tv but it did not fit and came up with this. I did put some sheets of rubber (cut from an old bicycle inner tube) under it to make it more stable and less likely to shift. ...
thingiverse
Went into Tinkercad and developed these TV risers about 2" tall (in total) with about 1.75" rise for the TV as I designed the feet of the TV to recess into the riser. ... The only thing I still want to add is a rubber pad or something on the bottom for...
thingiverse
I made these because the Yamaha Soundbar I have in front of the TV blocks the IR signal for the remote while you're sitting. It might be a good idea to use some anti slip mat underneath since it slides more easily with risers installed. However, I...
thingiverse
Bought a "TV Stand" speakers system, but my TV has the two feet and the speakers wouldn't fit under the TV. ... So I made these simple risers to lift the TV up a little.
thingiverse
I wanted the Sony tv (a KD-49X8505B) to have a bit more space under the tv to put a speaker in front or a ps4 below the tv with the standard legs. The OpenSCAD file is somehow parametrizable - you should easily change the height or the length of the...
thingiverse
My new TV was 1/4" too low for my Verizon set top box to fit under it. So I made these risers to lift it up. The recessed area to fit the TV foot is 9.25" x 1" the lift distance is .875" Measure your TV feet to check. You can easily scale this up or...
thingiverse
This is a riser voor a Samsung TV. This was necessary because the supplied stands were too low in combination with a soundbar. The parts raise the TV 4.5cm. ... The model in the pictures is ue32j5200aw.
cults3d
This is a riser voor a Samsung TV. This was necessary because the supplied stands were too low in combination with a soundbar. The parts raise the TV 4.5cm. ... The model in the pictures is ue32j5200aw.
prusaprinters
I made these because the Yamaha Soundbar I have in front of the TV blocks the IR signal for the remote while you're sitting. It might be a good idea to use some anti slip mat underneath since it slides more easily with risers installed. However, I...
thingiverse
I needed the TV a bit higher so made 4 of these these. Simple yet effective! The fill density can be quite low - I used 0.1 but use 0.3 to be on the safe side. ...At 0.3 I can put my full 90Kgs on one riser!
thingiverse
I'm using four 3d printed copies of this design to lift my 50" Vizio TV 2.25" off of the ground so I can fit my speakers underneath. ...They could be used to make room for a game console or other item under the TV.
cults3d
This is specifically for the LG 49UM6900PUA. ... It raises the TV up 34.75mm Each leg that this is designed for is 235 x 16mm. ...This landing zone is 236.5 x 20mm
thingiverse
In my case I use the TV's for side PC monitors and wanted to raise them to be level with my actual gaming monitor in the center of the two. By default, these are .625" high, but you can scale the model in your slicer to where you need them to be....
thingiverse
I had a problem where my Vizio soundbar blocked the IR receiver on my Samsung UHD TV. ...I designed these feet to go under the stock Samsung legs to raise the TV ~35mm so that the IR receiver isn't blocked.
thingiverse
This little block (well 4 of them actually) of PLA is/are currently holding my 55" LED TV 3" higher so I could fit my Center Speaker under it. :-D Cheers, be safe. ... Thingiview not working but support is coned out in the middle.
thingiverse
A tilted riser for the XiaoMi 33" TV Soundbar. Has an angle of 10°. Perfect if you have a lower TV setup and want the soundbar point directly at you :) Fits directly in the socket. ...Just peel off the rubber feet, place them under the soundbar and...
thingiverse
[protius2](https://www.thingiverse.com/protius2/designs) made this [television lifting shoe](https://www.thingiverse.com/thing:4719496) for the same TV but it was too tall for my needs. I downloaded the stl and re-made the model to the same...
prusaprinters
The Hisense HS214 soundabar doesn't quite fit between below the Hisense 43" Roku TV (why Hisense, why?) so I needed a part to raise it up.protius2 on thingiverse made this television lifting shoe for the same TV but it was too tall for my needs. I...
thingiverse
150mm high, 30 mm tall, can be scaled according to your needs. ... The size of the board on the photo is 800x200x16 mm. The TV weighs about 6 kg
thingiverse
this is a custom clip on which you can mount the side rail of your TMC to make a riser for your optics. you can use the screws from the side rails that come with your TMC, to attach the rail onto the clip, but you are going to need bolts for the...
thingiverse
Had to raise an IKEA LACK TV Bench up by 25mm, printed 4 of these for the purpose. ...CAUTION, stability of the end result is your responsibility, this design suited my purpose, it may not suit yours.