ritewing drak 3d models

Parts for my Ritewing Drak. All parts except the antenna mount holder designed for printing in TPU. ... https://www.youtube.com/watch?v=TzM5lwkQEVA

Ritewing Drak Nose. There is a version for Runcam2 and Foxeer 1177, and a version for Runcam2 and Swift/Eagle. Its not been printed and tested yet. ...Enjoy:-)

Wing joiner for the Ritewing (Big) Drak 60'' These things will join the fuselage and wings using an O-ring. The system replaces hook and loop tape. Reviewed model from Havardsa to fit a 120mm*120mm*120mm printbed This thing was modified with...

Various parts I used on my Big drak build

Hero 8 mount with FPV cam for big drak.

Print on its side, Can scale up or down depending on your needs, sized for a drak, so 60% for a mini drak and 30% for a nano perhaps?

I lost a couple of screw nuts of my Drak after a crash so I designed similar ones with Fusion 360. ... I printed this in PLA with 100 % infill and 0.2 mm layer height You find replacement screws here: https://www.thingiverse.com/thing:2431495

#Ritewing Mini Drak Control Horns Designed to fit as direct drop in for horns supplied in Mini Drak kit. **Recommended print materials:** 1. Nylon carbon. 2. PETG. 3. ABS **Print orientation** Everything can be printed normally (as shown).

These are all parts I designed and currently have printed and installed on one of my Full size (Big) Ritewing Drak's The nose piece is modular. This setup is designed for an HDZero Micro V2 camera and the HDZero 1 watt Freestyle VTX. THe VTX is...

Some parts I created for the Ritewing Mini Drak. VAS 1.3ghz BlueBeam Pro side feed Antenna cup. This is glued on to the top of the coroplast main hatch cover. The antenna lead drops in the vent behind it, as seen in the images below. ...

These things will join the fuselage and wings using an O-ring. The system replaces hook and loop tape. O-rings need to be 1/8 thick (section). Diameter depends on how tight you want it. 1 7/8 outer diameter feels good to me. 1 3/4 is tighter. ...2 is...

This one is for Gopro 3/4 and Foxeer 1177. ...Its never been printed or tested.

Replacement screw for the Ritewing Mini Drak and Drak. Recommend printing in thin layers to make good threads. ...I use 0.1mm layer height.

Ritewing Nano drak motor mount. Other mounts on here have various issues such as the plate gap being either too wide or too narrow, screw holes not the right sizes, etc. ... Edit: v2 has a thicker base

This thing holds different flight cameras and a Runcam 2 in the nose of the Ritewing Drak. The down tilt is 7 degrees from the assumed cord line. To install, cut 35mm from the tip of the nose. There is a cutting template to get the cut right. Let me...

The cable from the cam is too short to put the caddx into the side bay of the drak. In this design, you store the vista in a hole on the side of the front part of the wing. The outside part is inspired by muscle cars and there cooling system. You...

** I have my mod of Havardsa's Gopro 3/4 nose (https://www.thingiverse.com/thing:2859361) on my Drak but I just picked up a Gopro 7 which doesn't fit. I took the original and using tinkercad I enlarged the bay for the Gopro to fit the Gopro 7 (or 5...

The Drak's nose suits it's self well to cutting pockets for your FPV Camera or tic-tac shaped HD Camera. I however hate those cameras and prefer the GoPro session for my aircraft. The FPV camera pocket works with the HS1177 or HS1190 form factor...

I took Havardsa's nice design for a GoPro mount for the Drak and added the ability to wire a charging cable so the GoPro can be powered off a 5V regulator from the flight battery. Also added tunnels for that charge cable and for the FPV camera to...

Ritewing Mini Drak servo pockets are direct fit for Corona DS-339MG servos, those are low quality and very sensitive to 1.3Ghz video, they will rattle and behave erratically when the VTX is near by. I use BlueBird BMS-390DMH (Coreless) servos,...

This is a system I designed and developed for the Ritewing Nano-Drak. The concept places the RX and VTX antennas on the centerline of the fuselage for better aerodynamics, The flight components I use on my Nano Draks are: Matek F405-WMN FC APD-80F3X...

Made for the new gopro 9 black, and a runcam swift 4 degrees of down angle on the gopro Printed in tpu, 2 outer layers infill 25% 4 layers top and bottom

Everything is printed out of TPU. You'll need 4 skateboard bearings and 2 12g servos. This is setup to be printed out of TPU, the gopro is a press fit, printing this out of a rigid material will not work as designed. At the time of publishing...

A few Ritewing RC Mini Drak parts I came up with during my build. ...A "dog bone" style wing joiner, the vertical stabilizer inserts, and skids for the coro, which need to update.

Tired of the balsa wood I designed the ailerons for the Mini Drak. These ones are for small printers, like my Ender-3. ...They have a strong joint where to glue, hollow with reinforcements and a 2mm "skin" and a 20mm solid square where the horns are...

Easy and fast servo locating jig for Ritewing Nano Drak

... print. ABS plate version added - Full aero versions should fit the rear of the Drak fuse motor mount, but are heavier - Half aero versions as before, fit half the rear of the fuse motor mount Stinger = light protection Full guard = Heavy protection

Update: https://www.thingiverse.com/thing:4163668 Hero 5/6/7 mount for the ritewing mini drak FPV cam is fitted internally! ...Keeps it clean and protected Printed in TPU Camera is a Foxeer Mini size cam

Camera mount for molded Ritewing Nano Drak. Will fit a Foxeer Mini Predator. ...Put hot glue on the front of the camera to hold it into place, then glue it onto the nose of the ND.

A little support for the DJI Digital HD Camera that is designed for the nose of the RiteWing Mini Drak. ...Shown installed here - https://www.youtube.com/watch?v=X3dB_y7zsWc Happy flying!