rmrc nano skyhunter 3d models

This is a canopy i designed for the RMRC Nano Skyhunter. This holds the all in one camera that rmrc sells. The design is 3d Printer friendly as i designed it in 2 pieces. you will need (2) 2.5mm shcs bolts. Print the canopy vertical (front face)...

A 3D Printed Canopy for the RMRC Nano Skyhunter. They do include a canopy with the kit that would work just fine, but I wanted to make something that everything just fit into. It was made to use their Cricket Pro VTX, but anything smaller should...

Designed a battery tray to make swapping batteries in the Nano Skyhunter easier. This tray is designed to fit a Turnigy 3s 1300 pack. You may need to modify this design to fit your CG. ...The bottom layer is very thin so the tray is flexible enough to...

These are tail fins for the Nano Skyhunter.. they can be mounted on top or bottom and click into place... the 2 holes are for using two small zip ties to secure them. They should help with tracking and turning, and possibly remove some tail wag... I...

This is an all in one FPV mount for the Nano Skyhunter, it might work on other planes. It is designed for a standard HS1177 FPV camera, a Matek VTX-HV, including a mount for the SMA bulkhead that comes with the VTX. ... I glued it to the deck lid using...

This is an all in one FPV mount for the Nano Skyhunter, it might work on other planes. It is designed for a standard HS1177 FPV camera, a Matek VTX-HV, including a mount for the SMA bulkhead that comes with the VTX. ...I glued it to the deck lid using...

RMRC nano skyhunter top camera and vtx mount. Needs two 3mm screws. ...Might need a little tweaking with a heat gun to get it to the exact shape of your wing.

Skyhunter winglets. ...V2's are are 1mm thicker on the ends.

Skyhunter winglets. ...V2's are are 1mm thicker on the ends.

Here are the parts for the Vtol Nano Skyhunter. I will add the parameter files as I finish the project. ... It is still a work in progress.

Here are the parts for the Nano Skyhunter I built to learn Ardupilot. I will include the Parameter file as soon as I finish the built. ... It is still a work in progress.

I made this canopy to replace the standard foam canopy of my micro / nano skyhunter. Since Iam probably the only one still using a Immersion 600mw VTX I also included a blank model of the canopy so remixed can be made for other FPV setups. ... If you...

Bottom deck for the Nano / Micro Skyhunter. ...original was 2mm thick.

Bottom deck for the Nano / Micro Skyhunter. ...original was 2mm thick.

Motor mount for Nano / Micro Skyhunter. ...Original is 3.75mm thick, stl and dxf files are included for printing or cnc.

Motor mount for Nano / Micro Skyhunter. ...Original is 3.75mm thick, stl and dxf files are included for printing or cnc.

VTOL Arms for the Nano Skyhunter Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: No Resolution: 0.06 - 0.12 Infill: 25-50% Notes: Ended up printing 45 degrees diagonal to fit face down in the Ultimaker 2 Post-Printing

[](https://gfycat.com/forthrightambitiousairedale) The nano skyhunter comes with a cutout for a pan servo. I use and recommend the...

The elevator mount is an extended shroud that nicely holds things in place. The nano skyhunter comes with a cutout for a pan servo. I use and recommend the <a...

I got fed up with trying to repair the foam control surfaces on my Mini Skyhunter. So I created these, they're simple but effective and work with the control horns that come with the package. The plywood plates with blind nuts failed after a few...

HERE'S THE EXTENDED MOTOR MOUNT FOR THE NANO SKYHUNTER / MICRO SKYHUNTER / SKYHUNTER RACING. ALL 3 PLANES ARE THE SAME. I MADE THIS MOUNT WHERE I COULD INSTALL A 2204 SIZE MOTOR WITH OUT HAVING TO CUT THE FOAM. FITS PERFECTLY. ALSO UPLOADED MY LOGO...

Replacement sliding receiver plate for the RMRC Nano, or the Eachine Micro skyhunter. has a 30.5mm mounting hole arrangement for most modern flight controllers. make 2.2mm thick instead of 2, hopefully its a tight fit. DXF also included if you want...

Replacement sliding receiver plate for the RMRC Nano, or the Eachine Micro skyhunter. has a 30.5mm mounting hole arrangement for most modern flight controllers. make 2.2mm thick instead of 2, hopefully its a tight fit. DXF also included if you want...

A FPV pod for the caddx vista air unit to mount on to the Skyhunter racing/nano canopy. ...

Soporte para una micro camara FPV en el skyhunter nano, Imprimir 100% macizo y en la posición que está. Luego se puede sujetar al avión con los tornillos que traen los servos de 9g. Y la cámara también. Support for a micro camera FPV in the...

Replacement mounting piece for m3 screws that go through the wing area on the nano / micro skyhunter. I cut mine in half FOR REASONS so I needed a new one. ...This is a good approximation - jam an M3 captive t nut in those holes and you're good to go.

Replacement mounting piece for m3 screws that go through the wing area on the nano / micro skyhunter. I cut mine in half FOR REASONS so I needed a new one. ...This is a good approximation - jam an M3 captive t nut in those holes and you're good to go.

Instructions: 1) Attach standoffs to the holes in the mount 2) Attached your flight controller or GPS to the standoffs 3) Slide out the existing wood tray from the Nano Skyhunter 4) Place the mount in at a slight angle press into the slots in the...

Violently rammed a cc3d mount into my nano skyhunter receiver plate. What a kludge! Thanks for your hard work though altermac. Should work with ~16mm m3 screws, I'm using 18mm because that's what I had around. Go slow with a receiver mounted to it...

Violently rammed a cc3d mount into my nano skyhunter receiver plate. What a kludge! Thanks for your hard work though altermac. Should work with ~16mm m3 screws, I'm using 18mm because that's what I had around. Go slow with a receiver mounted to it...