robo 3d r1

Current versions: Shroud Cover- Used with: (Any RoBo 3D R1) Chain Connection Shroud Cover- Used with: (http://www.thingiverse.com/thing:696183) ===================================================================== The shroud and logo are printed...

... there was such a difference in mass on each side of the X-axis. ... Fill this with pennies and attach it to the left side as shown in the photo. Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: No Supports: No Resolution: 0.2

Length: 71mm Inner diameter: 30.3 mm Outer diameter: 52.5 mm Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 100% Notes: I used a raft, but only for security reasons. ...You...

... Now with an updated V2 Version! Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: No Supports: No Resolution: Medium-High Infill: 25-50% Notes:   Material: PLA Instructions Print this thing sitting up right.

As much as I like the Robo 3D R1, the LED lights are sooo bright I made covers for them. At night it lights up the room if I'm letting it run a long print. These just rest over the row of lights. ...Print 2 in the darkest color filament you have.

... No need for screws or any mounting stuff. Just slides right onto either side of the Robo 3D R1. This tool holder is obviously for MY tools, feel free to edit it for your tools. ...Takes about 22 hours to print.

... stuff. ...Just slides right onto either side of the Robo 3D R1. I use mine for hair spray, cooking oil, etc. Takes about 22 hours to print. "Storage Hanger" was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/1TGKpPyTHYf

... design works off compression. -ROTATE SCREW CAP AND PRINT AS VASE. Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: Doesn't Matter Supports: No Resolution: .2 Infill: .25 Notes: For thread caps change outer shell to .4.

this is a fan shroud for the robo 3d R1 printer with the all metal hot end. it is for a 40mm fan that is ducted around the X axis rod and exhausted directly on the heat sinks for the all metal hot end replacing the need for the tiny fan supplied. i...

Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: Doesn't Matter Supports: Yes Resolution: Medium-High Infill: 50-100% Notes:   Material: PLA Instructions   You will need a total of 38 chain links.     The process my vary...

(J'ai mis un peu de graisse dans le "bearing", cela ne semble pas amélioré le roulement qui est déjà correct.) #PRINT Bearing Centre Part 1.stl ;Flat larger face;layer 0.2;infill 30%;support=No Bearing Centre Part 2.stl ;Flat larger face;layer...

Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: No Supports: No Resolution: 0.2 Infill: 0.25 Notes: These are just the setting I used. ...I would imagine it would work the same with a different layer height and maybe more light...

The primary part of the project is the profiled top designed to create a flat platform that fits on top of the Robo 3D R1+. There are two .stl files for the top profile, one of which is blank, or flat, the other of which is grid which contains a grid...

This spool mount works with the Robo 3D R1 Plus+. ...Mount this on the top of your printer.

Z axis lead screw adapter for the Robo 3d R1 Print Settings Rafts: No Supports: No Resolution: .2 Infill: 15%

Made a spool holder for my Robo 3D R1 printer. ...Mounts at the top, and locks in place with a small locking piece.

... I will be testing this model fully, I have the original files for adjustment. Remixed from original Robo 3D R1 Plus Z/X axis carriers with a built in brace that connects to each other. ... Designed to be fully printed on a standard Robo 3D R1 Plus.

I cut a slot into the part designed by Mentaluproar in order to allow for it to be installed without taking apart the printer. ... It is meant to hold pennies, maybe other smaller things can work too. This is for a Robo 3d r1 printer.

I needed a logical way to connect my c270 WebCam to my ROBO 3D R1 so I made one, and now I am sharing it with you :)   Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: Doesn't Matter Supports: Yes Resolution: Medium-High...

The Robo 3D R1 and R1+ printers don't protect the USB plug from accidental impact. This simple part acts as a housing around the USB port to protect your R1 in case you accidentally elbow the USB plug. I simply super glued mine to the exterior of...

Soporte para rollo de filamento para Robo 3D R1 inspirado en el original. Se adapta perfectamente a la parte superior de la carcasa y es muy fácil de instalar, ofreciendo una máxima estabilidad y soporte. Hace que el cambio entre rollos sea sencillo...

A Z-bar brace for the Robo 3D R1 Plus which are designed to stabilize the Z-axis bars/threaded rods, and to mitigate vibration if used with optional vibration dampers (see below). Designed for use with a 608ZZ bearing which is pressed into the base...

This is stabilizer I made for my Robo 3d R1. I have the Z rods that go to the top of the case, so if you don't have that model these may not work without other mods. The large hole fits a standard size skateboard bearing (608 size). The small hole...

This is a simple carriage that adapts the Titan Aero extruder to the Robo 3D R1. Print with supports (v3 does not need supports). Mine was made with PETG. The two pictures have a version with changes to hold the cables on my system. The Light...

updated fan shroud is available at http://www.thingiverse.com/thing:1555114 Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: Doesn't Matter Supports: Yes Resolution: .200 Infill: 50% Notes: I sliced using Simplify3d which...

... ...The least I can do is cover up that ugly gaping hole. Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: Doesn't Matter Supports: No Infill: 100% Notes: May need a raft or some type of adhesion to stick to the build plate.

A remix of adamsgl's Robo 3D R1 Camera Mount with a slot to allow cameras designed to lay on top of monitors to be used. ...There are three models - the regular one will work if you want the camera to sit as shown in the pictures, the long model will...

... I threw it into Sketchup and modified it to be what I wanted. I used this LED; https://alofthobbies.com/led-lights-5822.html?___SID=S Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: No Supports: No Resolution: .2 Infill: 0.2

Cheap filament runout sensor mount for the Robo 3D R1 & R1+, designed to fit below most top mounted spool rollers when using normal 1kg or larger spools. Print as imported (sensor screw mount tab towards the build plate) with supports. Install by...

... the plug more stable. The offset may be a manufacturing hiccup in mine, but if it's like that in all of them this will help... Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: No Supports: No Resolution: 200 Infill: .10