robo r2 3d models

Robo R2 - Hotend 24V

https://robo3d.com/products/robo-r2

hotend clamp for the robo R2, made to fit an M3 nut for the clamping bolt instead of being threaded. ... i tested the mounting holes to just thread the bolts through and it seems to hold well

Robo R2 door catch. I used 6mm x 3mm magnets (2 off) and printed this in PETG 0.2 with support from build plate. ... Just slots into the existing holes, just make sure you get your magnets the right way around, I attached mine to the door first...

This part fits directly into the vacant hole for the second extruder in the Robo R2, and it helps smooth out the airflow from the tiny fan and around the hexagon extruder heatsink. ...

This is a simple fix to allow an E3D V6 to fit in a Robo R2 3d printer. Requirements are only M3 screws that are 6mm longer than the original ones. This part goes between the stock fan shroud and the carriage. INSTALLATION: 1) Remove fan...

We designed this spool stand to address the problem of our newest R2 not being compatible with our old generation filament. Our newest filament will be compatible with the R2. ...All of the files are ready to print without supports.

All this model does is raise the R2 printer 30 mm above the platform it is sitting on. ... There are no other benefits by using these feet, unlike the riser feet for the R1 series of printers.

Support axe Z robo R2 en PETG

Replacement fan shroud for the Robo R2 / C2 printer.

Have you ever seen a Robo R2 3D printing a Robo R2 3D printing a Marvin? Check out our Multi-Color Robo R2 USB Holder! ... Printed with Palette+: http://mosaicmanufacturing.com

Have you ever seen a Robo R2 3D printing a Robo R2 3D printing a Marvin? Check out our Multi-Color Robo R2 USB Holder! ... Printed with Palette+: http://mosaicmanufacturing.com

Have you ever seen a Robo R2 3D printing a Robo R2 3D printing a Marvin? Check out our Multi-Color Robo R2 USB Holder! ... Printed with Palette+: http://mosaicmanufacturing.com

Holder was laid flat on the print bed and turned at a 45 degree angle to fit the Robo R2 print bed.

Clips onto the door handle of a Robo R2 and holds the stylus so I don't loose it. ... Put up a new version at 12:35 on 1/15/18

A simple clip to go on the door handle of the Robo R2 3d printer and has a spot to keep your stylus. ...   New version added at 12:37 on 1/15/18.

Replaces the top of the stock Robo R2 / C2 extruder with this adapter to allow direct mounting of the E3D Titan Extruder. ... fixed 2 mm error in Titan placement.

... mount cleaner along with a singular unit that can be fixed on top if required. ... This is more compact and more ease to use filament cleaner for the Robo R2/ C2. This design makes it easy to oil if needed or simply just leave it as a cleaner. ...

I measured out the proper dimensions and created this scroll wheel mount for my Robo R2. I did not like the fact that without this mount, the scroll wheel is angled when you mount it on the R2. I wanted a stable, vertical mount without the angle on...

Based off of Angrybird12's R2 Guide Instead of running over the top, I'm going to try running along the side.

These two very small parts are added to the mount to address the 10° tilt Robo introduced with the incorrect mounting position of the Raspberry Pi camera. It addresses the error in timelapse video that is tilted 10°. ...Causes the OctoPrint interface...

I kept losing the thumb nuts off the heat bed of my Robo 3D printer. After searching the internet, (thingiverse in particular), I decided to try to create my own. Used a Caliper to get size. ...It only took two tries to find the right combo.

Allows you to mount a BMG extruder to the standard R2 mount. I printed this in PETG with support at 0.2mm layer height. I used some M3 countersunk 8mm screws to mount it to the carriage. You will also need to adjust your esteps in the eeprom menu...

The individual parts should work with the existing Robo plastic, but are designed to work together. To install the bronze bushings lightly coat a 6mm rod with oil and run it through a bushing so that the epoxy will not stick to the inside of the...

The clips are held onto the frame with Robo's existing screws and the screws hold the top of the LED mount. I did add double sided tape in between the 3D printed parts for extra security and to eliminate any rattling. I also added a small front...

Built in fusion 3d to hold 3 standard DS stylus.

This will allow you to print tall thin objects by directing all of the air flow to the tip of the nozzle. It allows you to use 13 mm overall length nozzles like CCTREE that are inexpensive and available from Amazon. This does not allow any airflow...

This printer fix block fits under the Z axis motor to stabilize the Z Axis from moving up and down during a print... ...which causes these rhythmic print lines

Created this to defect plastic debris fron getting caught between the touch screen and case causing screen from operating properly.

This is a spool drawer Remix which fits perfectly for the spool of 1/2 kilo of (light blue) filament shipped with the Robo3D R2 units.