robo3d e3d hotend v4 dual cooling fan mod

A CAD depiction is available for the E3D v6 Hotend, which features a built-in 30mm fan and offers a range of nozzle sizes between 0.1-0.6mm.

This is a mod for the Creality Ender 3 v2 to replace the stock 40mm hotend and part cooling fans with quieter 40x10 mm fans. The supply is 24V.</p><p>The arm was designed with a CAD model of the Ender 3 v2 but has not been tested. If you print it...

The design encompasses: * A mounting system to secure the extruder plate * A housing to accommodate the hotend * A bracket to support a 40x10 or 40x20 hotend fan * A duct to direct airflow from the original Creality blower fan * An LED mount and...

This is a mod for the creality ender 3 v2 to replace the stock 40 mm hotend and part cooling fans with quieter 40x10 mm fans. The supply is 24V. The arm was designed with a CAD model of the ender 3 v2 but has not been tested. If you print it feel...

Upgraded features are as follows: - better nozzel visability - an extra parts fan screw hole for stronger fan fixing - more space between parts fan the mounting plate surface - more defined jets to nozzel - BLTounch mount adjusted for less supports...

... creation. His front fan shroud design on both sides caught my attention, and I decided to incorporate it into my build. ...To ensure a secure fit, I had to clip and slide the rear shroud into place carefully, and now it fits snugly in its new home.

Take a few minutes to carefully tap two small holes that will securely hold the fan screws in place using standard M3 tapping technique. Use two specifically designed spacers, 6mm long and made from 3mm material, as demonstrated in a supporting...

DEPRECATED DESIGN Please be aware I am not developing this design any further. Microswiss_Cooling_Side_v1.1.stl for side mounting cables now uploaded. Upgraded features are as follows: better nozzel visability an extra parts fan screw hole for...

This is a 'Ender 3 v2 NEO Hotend Cooling Shroud for 4015 fan cover'

This is a very basic bracket to hold your BLTouch to your Robo 3D R1+ Printer. ... There are 2 options. You must have an aftermarket E3D V6 hot end installed for this to fit.

Several CR-10S parts cooling fans have shown impressive designs but unfortunately, some struggle to withstand minor snags on printing parts and require extremely small mounts (for the fan) that are prone to breaking. A brilliant solution would be...

The E3D V6 hotend cooling and fan holder is designed based on inspiration from the Internet. The aim was reducing weight and dimensions (mainly width) in order to make better use of the maximum printing area. With the current configuration, my...

A Sketchup illustration of the E3D v5 hotend was required by me.

It's also survived several hard crashes where an angry gorilla was trying to force the filament through when the extruder started grinding plastic - a situation that arises from dual extrusion without a mixing head. Some gcode snippets and hacks...

My goal was to maintain roughly the same distance between the nozzle and the bed as with both the volcano and normal E3D hotend designs without altering part cooling. ...I sourced an x-carriage from Thingiverse: https://www.thingiverse.com/thing:2437440

hotend

This is a holder designed specifically for the E3D Hotend, which can easily be attached to the RepRapPro x-carriage. It features space for mounting a 40mm fan at the front. ...To install the bowden tube, utilize a 5mm thread cutter and a 3mm one (after...

And from there, a modular mount was designed to take two E3D V6 hotends with an integrated fan like the original Prusa i3 mk2 design. Facing the fan of the left hotend towards the right reduced the width of the fan mount, leaving a small gap...

Create an appropriate part cooling fan for your Tevo Tarantula 3D printer, equipped with an E3D V6 Carriage and hotend. The duct features an internal baffle to improve air circulation within the duct. Select a 40x20 blower fan and print the part...

... X1 (V4) will allow you to obtain a good ventilation during your prints! ... Hardware needed: - Artillery Sidewinder X1 (V4) 3D printer - Bondtech BMG - E3D Lite 6 HotEnd - M3x5 screw (x2) - M3x16 screw (x2) - Washer for M3 screw (x2) - M3 nut (x2)

Keeping mass low on corexy or delta print heads is crucial, and this design allows part cooling without adding unnecessary complexity via additional fans. A slight modification was made to the internal profile of the duct to maximize airflow. (I've...

This is a precision E3D V6 Hotend holder designed with an integrated radial fan holder that provides reliable support for cable chain attachment of hotend wiring. A suitable hole is also included for securing a magnet used in Hall sensor endstops,...

The Cooling Duct for a Hotend is a vital component that plays a crucial role in maintaining optimal temperature control during 3D printing operations. Its primary function is to efficiently dissipate heat away from the hotend, thereby preventing...

I received this high-quality E3D type hotend direct from a Chinese manufacturer known for producing superior parts.

I construct a mounting bracket specifically designed to integrate an E3D V5 hotend into my Raise3D T3 3D printer system.

I made a part cooling bracket for my D-Bot build, replacing the blue fan shroud to cool down the hotend. It features two 40mm fans blowing directly downwards and has been performing exceptionally well so far. My only complaint is that it blows quite...

This is a revised remix of https://www.thingiverse.com/thing:2400384, optimized for use with an E3D hotend. Enhancements include: - A distinctive logo prominently displayed on the front - Prints without the need for supports and can be done without...

The original design was struggling to effectively cool the hotend, but this revised version has improved airflow that appears to be a major improvement. ...Unlike the previous model, which threaded bolts directly into plastic, this one uses 5.5mm...

I loved the design from https://www.thingiverse.com/mkloberg but I hate the stock part cooling fan so I took NBR's design and cut the Noctua fan part off and added it to the Taurus. ... The pictures show mkloberg V3.3 but I added the STL for his most...

This mount uses a 40mm fan for the hotend radiator, a model 5015 radial blower for cooling extruded material, and a bltouch sensor for automatic leveling of the heated bed. Parts to mount inductive and capacitive sensors had been added to the set. It...