robo3d e3d hotend v4 dual cooling fan mod

Upgrading the Stock E3D V6 Hotend Fan to a Dual Cooling System Requires Minimal Effort and Results in a Significant Boost to 3D Printing Performance.

I installed an e3d all metal on my anycubic mega-s and the metal duct was too big and dragged on the bed and the nozzle didn't reach. So I shrunk it and added a lip to have some support. ...I'll add the solidworks part to make a circular nozzle but I'll...

Unlike the original E3D fan ducts found on Thingiverse, which have a slightly smaller diameter for the cooling fins and therefore don't fit properly (being around ~25mm in diameter), this clone design allows more airflow than its predecessor due to...

Another 30mm fan mount designed for optimal heat dissipation, mirroring the concept behind this innovative design: https://www.thingiverse.com/thing:120249

Fan Holder Replacement The original fan air guides, measuring 40x40mm, are still employed to direct airflow. ...Print Settings Printer Brand: RepRap Printer Model: I3 Raft Generation: No Support Generation: No Resolution Setting: 0.2mm Infill Density:...

Required Materials 4x Hex socket screws (M3 x 45mm for Fan holder) 4x Compression springs (30.5mm diameter, 5.3mm thick) 4x Cross slot screws (M3 x 35mm for Fan Mount) 2x Hex socket screws (M3 x 35mm) + 2x M3 Hex nuts 1x Hex socket screw (M3 x 10mm...

Unfortunately my stock 30mm fan broke and i only have some 40mm fans lying around. So i created this mount for using a bigger fan. It does not collide with the heater block in any orientation, but as theres not much free space between the lower...

Another fan duct is all this printer needs.\nPrint Settings\nRafts: It's completely unnecessary.\n Supports: Absolutely not.\n Resolution: A mere 0.2 millimeters.\n Notes: Consider using a brim for better results.

This clip holds a 30mm fan securely in place on the E3D v6 extruder, firmly cupped into the cooling fins. ...Print Settings Printer Brand Ultimaker Printer Ultimaker 2 Rafts No Supports No Resolution 0.12 Infill na

Replacement for original fan holder. the original 40x40mm fan air guides are still used Print Settings Printer Brand: RepRap Printer: I3Rafts: No Supports: NoResolution: 0.2 Infill: 20% Notes: print on the flat side! Category: 3D Printer Parts

It's for a 40mm Fan. ...Twitter: https://twitter.com/Zep_To_ Facebook: https://www.facebook.com/umit.acku Google+:https://plus.google.com/u/0/109561398985315771625/posts Thingiverse:http://www.thingiverse.com/Zep_To 3D Print Community Germany:...

This is a 40mm fan project. You can find me on Twitter at @Zep_To_. I'm also on Facebook at facebook.com/umit.acku. My Google+ page is plus.google.com/u/0/109561398985315771625/posts. You can visit my Thingiverse page at thingiverse.com/Zep_To. The...

This E3D V6 Clone fan duct clips over the cooling fins, designed specifically for the Sunhokey Prusa i3 2015 printer. The original E3D fan ducts available on Thingiverse have a slightly smaller diameter that prevents them from fitting properly due to...

... cooling on all sides of the a part that I am designing so I needed something that could handle that. *Note* I used the mounting system of the E3D Hemera front-side 5015 part cooling fan mount (semi-usable) part but designed the rest on my own.

The cooling fan is designed for E3D mounted on a Solidoodle 3, combining print cooling and E3D airflow. However, there's no control over print airflow. Instructions include lining the inside of the cooling circle with HVAC or high-temp tape, printing...

A hotend cooling duct for the mk8 hotend that mounts with the same bolts that the hotend is mounted with. ...I've made it for my Quick Tool swap system, where print cooling is mounted to the swapped plate.

A compact dual fan specifically engineered to complement the E3D V6 hotend, boasting an aerodynamic design that maximizes airflow efficiency through expert manipulation of fluid dynamics principles. ...This powerful dual fan setup ensures optimal...

The problem was that the E3D has its own fan and it's hard to mount another print cooling fan because of the size. So I combined the two into one 40mm fan, which runs all the time. Two-thirds of the airflow goes to the E3D heatsink and one-third...

Design enhances existing cooling of E3D-V6 cold end, increases airflow of standard fan, and cools print according to height from bed. Fan rotates constantly at highest velocity, drawing most air from below with some drawn from cold end fan exhaust as...

This clip secures a 30mm fan to the E3D v6 extruder, held firmly in place by gently cupping the far side of the cooling fins. ... Print Settings Manufacturer: Ultimaker Printer Model: Ultimaker 2 Rafts: None Supports: None Resolution: .12 Infill: Not...

A combo of parts for the E3D v6 hotend cooling shroud and parts cooling. I modified parts from other folks to fit the v6 and added some extra bits. ...I can't find the link to the hotend shroud (I'll update it when I can). I crazy glued the duct to the...

40mm fan duct designed for active cooling on Creality CR7, CR8 and Afinibot 3D printers with Sybu hotend mount modification installed. This modification can be found at http://www.thingiverse.com/thing:1397731. ...For versatility, the part has been...

... for me. This cooler accommodates a standard 50x15mm radial cooling fan and requires only two M3 bolts for mounting. To my surprise, I didn't even need nuts - the bolts threaded right into place. ...Of course, nuts could still be used if needed.

I assembled a custom combo of parts for my E3D v6 hotend cooling shroud and parts cooling system, incorporating modified components from fellow makers to fit the v6 design and adding some extra features. Unfortunately, I lost track of the link to the...

I made this dodgy part cooling fan to be compatible with this E3D mount for the Ender 5 -https://www.thingiverse.com/thing:3682669 because I like the lightweight construction. While it is very much not a finished design it works and did okay in my...

Note: I've set my fan to 60% for perimeters and 30% for infill at around 80%, depending on the fan, the hotend can be cooled so much that it won't reach the desired temperature. Update: I added a second version that should be easier to remove...

A compact design for the E3D v6 and a 40mm blower fan is now complete, with a bolt interface added on one side to accommodate a probe bracket that will be installed later. Two additional mounting interfaces are also included on the blower side,...

I wasn't happy with the cooling shrouds that were out there and was needing proper cooling on all sides of the a part that I am designing so I needed something that could handle that.Note I used the mounting system of the E3D Hemera front-side 5015...

I recently lost power to my clone's fan, and I'm still waiting for my order from E3D to arrive, so I built this temporary fix until my new extruder gets here. ...This DIY setup uses the Radial fan mount design, specifically the [D-Bot / C-Bot Radial...

Had to edit it to fit on my HotEnd Fan(4020) but having space for the BLTouch on the right. ... It is a remix of: https://www.thingiverse.com/thing:4031637