rocket candy fuel 3d models
29591 3d models found related to rocket candy fuel.
thingiverse
Nozzles designed for high-power rocket with rocket candy fuel (sorbitol (35%) + potassium nitrate (65%)). 32mm nozzle desgned for 2MPa engine, 40mm nozzles A-B for 1,5MPa engines, and C-G for 6,5MPa engines. Every stub and nozzle must be...
cults3d
it is a rocket that can be used to decorate as well as to be sent into the air with homemade ergol BE CARFULL I'M NOT RESPONSIBLE FOR WHAT YOU DO WITH THAT ROCKET. ... SO BE CAREFUL.
thingiverse
Inspired by audin's remix of my other rocket here: http://www.thingiverse.com/thing:591805 See make with video by The3DPrint:https://www.thingiverse.com/make:381646 Instructions The example was printed on an Orion with 1.75mm T-Glase. Printed per...
thingiverse
Simple rocket model with a cone, two main cylinder sections, 4 wings, and 4 fuel boosters attached to the sides. ... Instructions Using OpenSCAD
grabcad
Test stand liquid fuel rocket reference design based on the book "HOW to DESIGN, BUILD and TEST SMALL LIQUID-FUEL ROCKET ENGINES" by Leroy J. Krzycki of RocketLab in 1967. ...Pdf of book is included in files.
thingiverse
made a model of a fuel injector from a Copenhagen rocket engine, best printed upsidedown without any internal supports.
thingiverse
Parts for a small liquid fueled rocket engine that I designed using equations from "How to Design, Build and Test Small Liquid-Fuel Rocket Engines." Would burn kerosene and LOX at 0.75 lb/sec at a mixture ratio of 2.2 and a thrust of 191 lbs. ISP of...
grabcad
Test stand liquid fuel rocket reference design based on the book "HOW to DESIGN, BUILD and TEST SMALL LIQUID-FUEL ROCKET ENGINES" by Leroy J. Krzycki of RocketLab in 1967. ...Pdf of book is included in files.
grabcad
this is a rocket Nozzle, calculations are not verified, the flow should be appropriate by using the right amount of fuel for a Type G rocket,i personally recomend using a mix of Aluminium powder and potassium nitrate (Al+KNO3) as a solid fuel.
thingiverse
V2 / A4 Rocket, liquide Oxygen and Fuel ( Alcohol ) Tank These fuel tanks are 1/12 scale, made to match the "V2-mod 1944" model rocket engine from www.accuraspacemodels.com. It follows the input flange of the turbo pump. I made it closely to...
grabcad
Back mounting system for 88 ft2 N2 tank and two D2 H202 fuel tanks.
thingiverse
Rocket fins for a solid fule rocket. ...Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter ...
thingiverse
c'est une fusée qui peut être utilisée pour décorer comme pour être envoyée en l'air grâce à de l'ergol maison BE CARFULL JE NE SUIS PAS RESPONSABLE DE CE QUE VOUS FAITES AVEC CETTE FUSEE ALORS FAITES ATTENTION
thingiverse
Like mechg's original, this is designed to be spiral printed. I printed this on a Rostock Max v2 at 0.2mm layer height, 0.4mm wall thickness, scaled 2.5x, sliced using Cura, printed in clear ABS at 50mm/s at 235C. The result is about 15 inches...
thingiverse
Mold and compression tooling for assembling R-Candy rockets using 3/4" Schedule 40 PVC. Required Materials: 5" length of Schedule 40 3/4" PVC pipe 3/4" dowel rod to rest nozzle mold on for compression Bentonite Clay KN03/Sugar propellant...
3docean
3D model of Candy Environment, materials, lights, render settings included, Global illumination render settings
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: hole_radius = 2 Font = write/orbitron.dxf stick_thickness = 3 message = Candy font_size = 15 font_thickness = 6 stick_width = 8 flat_bottom = 1
thingiverse
... http://www.thingiverse.com/thing:117519 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=117519 Instructions Using the following options: Your_Text = CANDY Text_Rotate = 0 Text_Size = 11 Text_Font = write/knewave.dxf
3docean
Please don’t forget to rate the model, for us it is very important 3D model available in these formats: 3ds Max 2010 (.max), Autodesk FBX 2006 (.fbx), OBJ (.obj) Scene Statistic below: Polys: 12 399 Tris: 12 400 Edges: 18 641 Verts: 6 243 - Scale of...
prusaprinters
<p>This was created in Fusion 360 as practice work for me. ...The model here was scaled up to 200% to better show detail and functionality. </p><ul><li>Printed with Prusament PLA. </li><li>Standard Infil</li><li>You will need to add supports...