rod wrapping stand 3d models
222391 3d models found related to rod wrapping stand.thingiverse
These three parts are to create a fishing rod wrapping lathe based entirely on aluminum extrusion. The parts are about 6" in height (5" in height from the bed). It does not include a lathe bed, you can purchase two raw aluminum extrusion bars to...
cults3d
THIS IS STILL A WORK IN PROGRESS Should be good to print but I have not printed it yet Use 1/4" rod for carriage, and 1/8" threaded rod with springs for the spools. Designed to use #19 single strand wire for tension bars but you can use wire coat...
thingiverse
This is a collaborative project and once a few rod builders use this to build rods, I will be collecting feedback and suggestions to make this project more advanced. Use 1/4" rod for carriage, and 1/8" threaded rod with springs for the spools. ... ...
thingiverse
The stand is suitable for a winter fishing rod with a 3.6mm diameter stick
cults3d
STL file to print your own Pretzel rod stand to make dipped pretzels easier and also for display. ... Dimensions: 7 1/4 x 5 1/4 x 1 Hole is 15 mm in diameter with a little lip to hold the pretzel rod securely, and is 20mm deep.
thingiverse
This is a headphone stand in the sape of a connecting rod. When printing you may wanna use supports, because of the ring sections. I have printed this modell standing up with supports, and it came out really nice. ... Hope you guys enjoy the design.
thingiverse
... to time. This is not an exact replacement. I don't need to screw these stands (if I did, I probably would not lose them). Notes ----- Print in ABS or other filament that can handle the surface temperature of the golden rod without distorting. ...
thingiverse
A simple stand for tubes and rods; 2-20mm; holes for wall mount on the back 3 mm Birchwood, cutouts are arranged for one sheet 600 mmx400 mm Settings in Lightburnfile are for my 60W CO2 Laser Cutting time: approx. ...20min As usual: I appreciate...
prusaprinters
Create a glow-in-the-dark uranium rod with its own stand.What you will need:A test tube with a diameter of 16 mm and a height of at least 160 mm.Epoxy resin.Glow in the dark powder (Strontium Aluminate).
cults3d
A simple stand for tubes and rods; 2-20mm; holes for wall mount on the back 3 mm Birchwood, cutouts are arranged for one sheet 600 mmx400 mm Settings in Lightburnfile are for my 60W CO2 Laser Cutting time: approx. ...20min As usual: I appreciate...
thingiverse
... Note: You will have to print the clamp (https://www.thingiverse.com/thing:1982907) and the small easle + rod (included as seperate STL's in here, but can also be found https://www.thingiverse.com/thing:1982909) to get the setup from my picture.
grabcad
... machine with a modified Supporting Arm. ...Included movies show the machine in action.The "wrapping lines" are "animated as circular" but the actual wrapping happens on the rectangular profile of the wrapped product (with proper forces estimation).
grabcad
This is project of pallet wrapping machine made as a thesis at Technical University of Lodz
thingiverse
Front and back (left & right) fishing rod support. ...To be used with M6 nut / bolt. The small lips on the back support is so you can hang your strop next to the rod.
thingiverse
You will need cca 30mm threaded rod - BSF 3/8", you can use old thread from broken one.
thingiverse
... each side. Instructions Print two out (one for each side) Cut a 1 3/16" diameter rod to length. Slide the spools on and then the ends. I printed on M3D with Medium quality and Low fill. ... I included the .123dx file if you want to change it.