rode mic holder 3d models
331958 3d models found related to rode mic holder.thingiverse
This Mount is much smaler than the original. ...but you need the original Mounting plate.
cults3d
This model is offered for free please consider subscribing or liking one of my videos on YouTube just follow the link below: https://fsc.co.nz/thanks-for-the-free-stl I designed this as I found other models were too tight to fit the mic and the hole...
thingiverse
GoPro Rode shotgun microphone holder, meant to be used with GoPro camera swivel mounts. Microphone is intended to slide into the mount via the side with the filleted edge. ...Recommended to print part with the 'tube' vertical, non-filleted edge down.
thingiverse
Adapter for Rode Boom Mic (Videomic) Instructions Adapter for the end of the boom stick for a Rode Videomic. This particular adapter attaches to the shock mount and is measured to the Rode Directional Video Condenser Microphone. The tolerance for the...
thingiverse
two pieces to make a mount for a rode mic to clip onto a DJI osmo 2
thingiverse
This is designed to attach to the vertical sliding rod with the threaded end giving the Rode clamp something to grab onto. It works well enough. Though, there is now extra weight that the mic stand wasn't made to carry. ...I have to be careful that the...
thingiverse
I bought my Rode NT-1 used and it was missing the nut that secured the mic to the shock mount. Searching around online there was a metal option for $25 but I bought this mic used to save money, not spend more. This is the 3rd iteration I have made...
thingiverse
Cable clip to stop cables flapping in the breeze. ...Fits my Rode boom, might fit others with a 13.2mm square construction.
thingiverse
Love this Mic but the supplied clip was not very good. ... Designed and printed a load of my own for use on location.
thingiverse
Instead of buying the extender arm(s) that will allow the DJI Osmo to support the small Rode microphone that DJI sells as an accessory to the Osmo, printing this adapter will allow your microphone to grab on to the phone mount that comes with the...
thingiverse
This is a fiching rode holder made for a rode of 0,4 and 1 cm of diametre . ... C' est pour attacher une canne a pêche une fois pliée avec un côté de 0,4cm et un autre de 1cm
thingiverse
Replacement for a broken mic stand mount for the Rode NT-1a condenser mic
thingiverse
Basic useful cable clip for the Rode PSA1 desk mic arm. Drawn in Fusion 360. ...
cults3d
Basic useful cable clip for the Rode PSA1 desk mic arm. ...Drawn in Fusion 360.
thingiverse
this is a mic flag for rode reporter mic that holds a raspberry pi zero and a 2.5 inch screen for display graphics or video on your flag. ...there should be enough room to fit a lipo
myminifactory
... when I needed an interview mic for Formnext 2017. ...Rather than buy a new mic, I just printed out this handle so I could use my RODE smartLav+ lavelier mic as a handheld. ...It's pretty small, but looks professional enough if you're in a pinch!
thingiverse
A clip to mount 2 mics on a old version Rode blimp. This is for one mic 22mm diameter and one 19mm diameter. I used the Dual Mic Drum Clip MK1 by Emil_Mathiesen and the Sennheiser MKH clip (D.19mm) by PierreB and just combined them. I am a...
thingiverse
This is a wall or table mount 4 mic Rode Wireless Go II charger. I made it a little bigger so that it can allow for a protective case on your mics. This is the usb cord that I used: ...
thingiverse
This is a small clamp to secure a Lav Mic inserted into the Rode Wireless Go, so it can't be tugged out of the non-locking 3.5mm jack by accident. The rubber band is not even obligatory for it to work. it clamps just fine without it. It is just...
myminifactory
1. ...Replacement for the Rode-USB-Microphone tripod-mount . 2. ...Additional horizontal mount.
thingiverse
To protect my Rode wireless Go i made this case to print in TPU or TPE. ... https://www.youtube.com/watch?v=OKbjh9dY-ro
thingiverse
I needed an adapter to hang my rode nt usb mini from the dampener adapter thats attached to the boom arm
thingiverse
This is just a test of my design to wall mount my rode nt-usb microphone. ...I am unsure if the hole is the exactly correct diameter, but it should be about right.
thingiverse
I made an adapter for my camera-mic, so i don't have to buy a new one for my PC. It points some what at my mouth. ...works good :)
prusaprinters
This is an extreme Simple Microphone Spider for my Rode NT USB Mini. You need two rubber bands to create the swing effect. I used two hair ties with 60 mm in length. Every rubber band should work. ...I assume that is also will work with other standing...
thingiverse
... You could technically print as many arms as you want and extend it to your liking, also I designed the base around a mic arm clamp I had lying around but I guess you could edit it to make it compatible with whatever kind of clamp you have/print.
prusaprinters
To protect my Rode wireless Go i made this case to print in TPU or TPE. Print Settings Rafts: No Supports: NoResolution: 0,2mm Infill: 15% Filament: any brand TPU or TPE Notes: No Support needed Category: Camera
thingiverse
I decreased the length of the gripping arms slightly to reduce the gap that allows this adapter to slide along the phone holder and rattle. ...Print Settings Printer Brand: RepRap ...