rode microphone holder 3d models
333489 3d models found related to rode microphone holder.thingiverse
... higher then the original one and it will not break from the mounting of the Microphone like the original one. . Because it is higher than the original one the Flash of the camera is accessable and works fine with the mounted microphone. ...
thingiverse
RØDE (Rode) VideoMicro Microphone Desktop Holder Remix from DIYMacLeod
thingiverse
These holders are for supporting the Rode M5 mics at a 110 degree angle to each other within the Rode Blimp 2 windscreen. A standard XLR connector will not fit on the back of these mics in this configuration, you have to get creative and fabricate a...
thingiverse
GoPro Rode shotgun microphone holder, meant to be used with GoPro camera swivel mounts. Microphone is intended to slide into the mount via the side with the filleted edge. ...Recommended to print part with the 'tube' vertical, non-filleted edge down.
thingiverse
Base stand for rode microphone VideoMicro. No supports required. Additional Hardware: - m3 screw - m3 nut for locking mechanism. ...
cgtrader
This is the 3d model of the one of the model RODE microphone. There are different formats inside the project. ...C4D, Max, OBJ, FBX
cults3d
180x180x210 Is the size of the print good for: Rode NT1, NT1-a, NT1000 Rode NT2, NT2-a, NT2000, K2 Rode Broadcaster Rode Procaster Rode NTK
thingiverse
180x180x210 Is the size of the print good for: Rode NT1, NT1-a, NT1000 Rode NT2, NT2-a, NT2000, K2 Rode Broadcaster Rode Procaster Rode NTK
thingiverse
rode wireless go is good for self video, but not for interview. ... I design this stick to make it more like normal microphone. rode wireless go 是款很隨身的麥克風 但是卻不太適合訪問時使用 這根棒子可以讓它用起來更像一般麥克風
thingiverse
This is a quick design I did for the Rode Interview Go microphone that works with Wireless GO II microphones. This quick and easy print gives you a three sided triangle perfect for applying your decal, or a printed plaque. ... Simply slide it over the...
thingiverse
This is a handle for the Rode Wireless Go Microphone. Designed in Autodesk Fusion 360. ...**Make sure to make your brim nice and wide** so that the model doesn't wobble as the print job gets close to being finished (and quite tall).
thingiverse
This is a case that holds the RODE Wireless GO II microphone set. 3mm x 6mm magnets are used to hold the lid. They are tight, and I just hammered them in with no glue. If you reduce the size of the lid in both directions by 1 mm it will be a friction...
thingiverse
This is a fiching rode holder made for a rode of 0,4 and 1 cm of diametre . ... C' est pour attacher une canne a pêche une fois pliée avec un côté de 0,4cm et un autre de 1cm
prusaprinters
Summary A remix of FDMBRO's NT-USB Dust Protector modified to fit the Rode Procaster microphone without a wind\popshield. Print SettingsPrinted on a Prusa Mini - from the flat end (with the mic logo) up in PLA with the standard 0.2mm...
grabcad
I created this adapter to allow me to use the rode videomicro as a sound recording setup with my gorilla pod. Used a brass threaded insert for the 1/4-20 screw hole on the bottom of the part. ...This was printed using a prusa mk3s with PETG.Threaded...
cults3d
Ortho-planar spring inspired anti shock mount for Boya by-mm1. ... I've managed to reduce mount noise using this microphone mount in my filming rig.
thingiverse
Ortho-planar spring inspired anti shock mount for Boya by-mm1. ... I've managed to reduce mount noise using this microphone mount in my filming rig. ...
prusaprinters
After the shockmount of my RODE VideoMicro broke, I designed a new one that could replace the original Rycote mount. Both PLA and PETG have worked well for me. The original hardware of the coldshoe mount can be used to mount the print. The noise...
thingiverse
Røde microphone attachment/holder. 100% infill for best strength. ... 0.2 layer hight
thingiverse
Camera attachment for Rode Microphone Wireless Go with 1/4 inch thread. Printed in PETG. ... Empiricus@Dremomys
thingiverse
A simple clamp to prevent the the RODE PSA1 microphone studio arm from swinging out while not in use.
thingiverse
Clamps to the lower body of a gimbal, allowing you to mount a Rode microphone (or anything with a hotshoe-style fitting).
thingiverse
I have a DJI OSMO, Rode microphone/receiver, and a tripod that don't like to play together. ...This adapter helps everyone get along.
cults3d
This design uses a hinge method to securely lock a 3.5mm lavalier cable into the Rode Wireless Go II (and should work for Rode Wireless Go I). Simply print, and attach. The trick is to insert the microphone cable first, then press everything in...
thingiverse
Poignée pour microphone Rode NT-USB et support articulé Neweer. Elle est imprimée sur Artillery Sidewinder X2. ... Conseil d'impression - Nécessite des support (en contact avec le plateau) - Pas d'accroche spécifique (jupe) - Remplissage 33% -...
thingiverse
A easy support system for my Rode M5 matched pair Microphones to record in XY-Stereo Mode. Center hole is a microphone thread 3/8" to mount it directly on a microphone stand. The two other holes have on the top also a 3/8" thread to prevent the...