rode psa 1 3d models
887112 3d models found related to rode psa 1.thingiverse
Wire clip to mount on RODE PSA 1 Swivel Mount. ...Designed in Fusion 360.
thingiverse
Found this microphone clip for the Neewer Microphone Stand (https://www.thingiverse.com/thing:2217082) and modified it to fit on the RODE PSA-1. Will probably fit on other similar microphone arms with 10mm wide beams. ... Prints without support...
cults3d
Found this microphone clip for the Neewer Microphone Stand (https://www.thingiverse.com/thing:2217082) and modified it to fit on the RODE PSA-1. Will probably fit on other similar microphone arms with 10mm wide beams. ... Prints without support when...
thingiverse
Simple headphone holder for the Rode PSA 1 boom arm (not for the cheaper ones, they are usually thinner than the PSA 1 (13.5mm)). Works just fine and fits perfectly. If it doesn't fit, scale the X and Y axis a bit up or down. ... About 1 hour print...
thingiverse
Wall mount for articulated microphone arms, specifically the RODE PSA-1. The only manufactured one I could find was $25, had 3 holes, only 2 of which would fit on a single 2x4 stud. This wall mount is designed specifically for mounting to a...
cults3d
Wall mount for articulated microphone arms, specifically the RODE PSA-1. The only manufactured one I could find was $25, had 3 holes, only 2 of which would fit on a single 2x4 stud. This wall mount is designed specifically for mounting to a stud,...
prusaprinters
It is a press fit onto the thumb nut that the PSA-1 table screw mount is supplied with.
thingiverse
This is a remix of a Manfrotto 504 Plong tripod quick-release plate, that allows a Rode PSA1 boom arm to be mounted on top of the tripod.
thingiverse
A little piece to adapt the notches to turn the mount of the SM7B 90 degrees, so that the output jack is oriented 90 degrees turned, because I had problems with the clearance with my boom arm but theres more than enough space on the "underside". ...
thingiverse
Rode PSA-1 microphone boom arm wall mount. ...Will most likely work with other microphone arms that have a 13mm diameter shaft that go into the base.
thingiverse
A 3d print to mount the Rode ai 1 to the underside of a desk. Designed to print without supports (NOT in the preview orientation). ... Mounted with m3 self tapping screws of whatever length necessary.
thingiverse
I bought my Rode NT-1 used and it was missing the nut that secured the mic to the shock mount. Searching around online there was a metal option for $25 but I bought this mic used to save money, not spend more. This is the 3rd iteration I have made...
cults3d
I didn't find any affordable desktop stand for my microphone, so I created one. ... This stand suits perfectly for the RODE NT1-A microphone. ... If you need a custom one for another model, just send me a message and we will design it for you!
thingiverse
This is the Rode Neusje, bought to Amsterdam from Hoorn, and currently undergoing a refit, including a new polytarp lugsail and a mast and boom brought 42km on a bicycle from the forest of Lage Vuursche. Now available in HO scale - perfect for...
thingiverse
Dji Osmo Pocket 1 versiyonunu, Rode Video Mic ile bağlar. Bunu yaparken Tripod bağlantı nottası altta bulundurur. ...Ayrıca go pro adaptörleri ile uyumludur.
thingiverse
y splitterbox for custom low profil xlr to 1/8 for rode wireless go cable is small mogami 22-2 shielded screw are m2 cap hex nut are m2 hex
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=681203 Instructions Using the following options: cut_height_percent = 0.7 direction = "up" baseheight = 1 text_excenter = 15 fontfilename = write/orbitron.dxf textstring = 1ST PLACE PSA WSTL...
thingiverse
This is a stand for PSA card, the first 2 files will fit a psa card with a sleeve, The thirld one is a little longer for a not so tight fit. I would recommend to print this with at least 30% infill or more to give the stand some weight to it so...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Instructions Using the following options: Loop_character = o Loop_font = Chewy Text = PSA spacing = [15,12,13] Loop_x_position = 11 height = [5,6,4] twist = -3 Rotation = 50 center = 60...
thingiverse
I wanted to mount my interface vertically, so I made this. No supports required, just print in place. ...The cable that comes with the interface will sit underneath the interface just lightly coiled up with the USB-A side poking out the hole, ready...
thingiverse
This is a fiching rode holder made for a rode of 0,4 and 1 cm of diametre . ... C' est pour attacher une canne a pêche une fois pliée avec un côté de 0,4cm et un autre de 1cm
cgtrader
This model is built very near to scale within a few inches of actual general dimensions and is fully textured. This model has animateable flaps, ailerons, landing gear, landing gear doors, elevators, and rudder. ...It is available in 11 different...
cgtrader
This model is built very near to scale within a few inches of actual general dimensions and is fully textured. This model has animateable flaps, ailerons, landing gear, landing gear doors, elevators, and rudder. It is available in 11 different...
thingiverse
This object is a replica of Rode Microphones VideoMicro. There is a 3.5mm jack jack on the back. ... After a few excavations, the retaining part has expanded in my case due to the type of material but with PET-G this can be completely avoided.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1013494 Instructions Using the following options: lettering = Rode Uien labelStyle = Indent textNudgeY = -2 textNudgeX = -10 style = Pacifico indentEdgeWidth = 1.05 labelDepth = 2 stickLength =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1013494 Instructions Using the following options: labelDepth = 2 textHeight = 2 style = Pacifico labelHeight = 20 labelStyle = Indent oneOrTwoSticks = One labelWidth = 96 stickWidth = 10...
thingiverse
... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=78727 Instructions Using the following options: build_plate_selector = 0 label_text = rode peper build_plate_manual_y = 101 build_plate_manual_x = 104 font = write/Letters.dxf